Datasheet
2002 Microchip Technology Inc. Preliminary DS39598C-page 123
PIC16F818/819
Supply Current (IDD)
(2,3)
PIC16LF818/819 7 TBD µA -40°C
F
OSC = 31.25 kHz
(Internal RC Oscillator)
7TBDµA 25°C V
DD = 2.0V
8TBDµA 85°C
PIC16LF818/819 16 TBD µA -40°C
14 TBD µA 25°C V
DD = 3.0V
13 TBD µA 85°C
All devices 35 TBD µA -40°C
28 TBD µA 25°C V
DD = 5.0V
25 TBD µA 85°C
PIC16LF818/819 111 TBD µA -40°C
F
OSC = 1 MHz
(Internal RC Oscillator)
116 TBD µA 25°C V
DD = 2.0V
122 TBD µA 85°C
PIC16LF818/819 164 TBD µA -40°C
162 TBD µA 25°C V
DD = 3.0V
165 TBD µA 85°C
All devices 278 TBD µA -40°C
266 TBD µA 25°C V
DD = 5.0V
266 TBD µA 85°C
PIC16LF818/819 288 TBD µA -40°C
F
OSC = 4 MHz
(Internal RC Oscillator)
294 TBD µA 25°C V
DD = 2.0V
299 TBD µA 85°C
PIC16LF818/819 441 TBD µA -40°C
428 TBD µA 25°C V
DD = 3.0V
428 TBD µA 85°C
All devices 791 TBD µA -40°C
752 TBD µA 25°C V
DD = 5.0V
747 TBD µA 85°C
15.2 DC Characteristics: Power-down and Supply Current
PIC16F818/819 (Industrial, Extended)
PIC16LF818/819 (Industrial) (Continued)
PIC16LF818/819
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
PIC16F818/819
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with
the part in SLEEP mode, with all I/O pins in high-impedance state and tied to V
DD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all I
DD measurements in active Operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be estimated
by the formula Ir = V
DD/2REXT (mA) with REXT in kΩ.