Datasheet

 2010-2011 Microchip Technology Inc. Preliminary DS41440B-page 357
PIC16(L)F1825/1829
30.3 DC Characteristics: PIC16(L)F1825/1829-I/E (Power-Down)
PIC16LF1825/1829
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC16F1825/1829
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D022 — 0.03 1.0 2.7 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.08 1.75 3.3 A3.0
D022 — 17.8 31 35 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 20.5 40 45 A 3.0
— 21.7 45 50 A 5.0
D023 — 0.2 1.5 3.0 A 1.8 LPWDT Current (Note 1)
— 0.5 2.0 3.7 A3.0
D023 — 18 32 36 A 1.8 LPWDT Current (Note 1)
— 20.9 42 48 A 3.0
— 22.1 45 52 A 5.0
D023A — 12.6 22 25 A 1.8 FVR current (Note 1)
— 12.8 24 27 A3.0
D023A — 32.7 50 55 A 1.8 FVR current (Note 1)
— 39 60 65 A 3.0
— 69 100 110 mA 5.0
D024 — 7 14 16 A 3.0 BOR Current (Note 1)
D024 — 24 40 43 A 3.0 BOR Current (Note 1)
— 27 45 58 A 5.0
D025 — 1.1 4.5 5 A 1.8 T1OSC Current (Note 1)
— 1.3 5 5.5 A3.0
D025 — 19 33 36 A 1.8 T1OSC Current (Note 1)
— 21.6 38 45 A 3.0
— 23 46 50 A 5.0
D026 — 0.05 1.5 3.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.07 2.0 3.5 A3.0
D026 — 17.8 32 42 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 21 36 46 A 3.0
— 22 40 48 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.