Datasheet

 2010-2015 Microchip Technology Inc. DS40001419F-page 241
PIC16(L)F1824/8
25.2.6 SPI OPERATION IN SLEEP MODE
In SPI Master mode, module clocks may be operating
at a different speed than when in Full Power mode; in
the case of the Sleep mode, all clocks are halted.
Special care must be taken by the user when the
MSSP1 clock is much faster than the system clock.
In Slave mode, when MSSP1 interrupts are enabled,
after the master completes sending data, an MSSP1
interrupt will wake the controller from Sleep.
If an exit from Sleep mode is not desired, MSSP1
interrupts should be disabled.
In SPI Master mode, when the Sleep mode is selected,
all module clocks are halted and the transmis-
sion/reception will remain in that state until the device
wakes. After the device returns to Run mode, the
module will resume transmitting and receiving data.
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This
allows the device to be placed in Sleep mode and data
to be shifted into the SPI Transmit/Receive Shift
register. When all eight bits have been received, the
MSSP1 interrupt flag bit will be set and if enabled, will
wake the device.
TABLE 25-1: SUMMARY OF REGISTERS ASSOCIATED WITH SPI OPERATION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Register on
Page
ANSELA
— — —ANSA4 — ANSA2 ANSA1 ANSA0 122
ANSELB
(1)
— — ANSB5 ANSB4 — — — — 128
ANSELC
ANSC7
(1)
ANSC6
(1)
— — ANSC3 ANSC2 ANSC1 ANSC0 128
APFCON0
RXDTSEL SDOSEL
(2)
SSSEL
(2)
— T1GSEL TXCKSEL
— —
117
INLVLA
(3)
— — INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0 123
INLVLA
(4)
— — INLVLA5 INLVLA4 INLVLA3 INLVLA2 INLVLA1 INLVLA0 123
INLVLB
(1)
INLVLB7 INLVLB6 INLVLB5 INLVLB4 — — — — 128
INLVLC
(3)
INLVLC7
(1)
INLVLC6
(1)
INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 134
INLVLC
(4)
INLVLC7
(1)
INLVLC6
(1)
INLVLC5 INLVLC4 INLVLC3 INLVLC2 INLVLC1 INLVLC0 134
INTCON GIE PEIE
TMR0IE INTE IOCIE TMR0IF INTF IOCIF 89
PIE1
TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE 90
PIR1
TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF 93
SSP1BUF Synchronous Serial Port Receive Buffer/Transmit Register 234*
SSP1CON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 281
SSP1CON3
ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 283
SSP1STAT SMP CKE
D/A P S R/W UA BF 280
TRISA
(3)
— — TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 121
TRISA
(4)
— — TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 121
TRISB
(1)
TRISB7 TRISB6
TRISB5 TRISB4 — — — — 127
TRISC
(3)
TRISC7
(1)
TRISC6
(1)
TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 127
TRISC
(4)
TRISC7
(1)
TRISC6
(1)
TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 127
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the MSSP1 in SPI mode.
* Page provides register information.
Note 1: PIC16(L)F1828 only.
2: PIC16(L)F1824 only.
3: Unshaded cells apply to PIC16(L)F1828 only.
4: Unshaded cells apply to PIC16(L)F1824 only.