Datasheet
2011 Microchip Technology Inc. Preliminary DS41441B-page 329
PIC12(L)F1840
30.3 DC Characteristics: PIC12(L)F1840-I/E (Power-Down)
PIC12LF1840
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC12F1840
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D022 — 0.02 1.0 4.0 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.03 1.1 4.8 A3.0
D022 — 5 20 30 A 2.3 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 5.6 22 32 A 3.0
— 6.0 24 34 A 5.0
D023 — 0.3 1.5 10.5 A 1.8 LPWDT Current (Note 1)
—0.52.0 16 A3.0
D023 — 5.3 21 31 A 2.3 LPWDT Current (Note 1)
— 5.9 23 33 A 3.0
— 6.3 25 35 A 5.0
D023A — 3.3 25 35 A 1.8 FVR current (Note 1)
— 3.4 27 37 A3.0
D023A — 19 55 60 A 2.3 FVR current (Note 1)
— 20 65 70 A 3.0
— 21 70 80 A 5.0
D024 — 6.9 15 20 A 3.0 BOR Current (Note 1)
D024 — 9.5 35 40 A 3.0 BOR Current (Note 1)
— 11 40 45 A 5.0
D025 — .74 4.0 7.0 A 1.8 T1OSC Current (Note 1)
— .86 4.5 7.5 A3.0
D025 — 5.1 20 30 A 2.3 T1OSC Current (Note 1)
— 6.0 22 32 A 3.0
— 6.2 24 34 A 5.0
D026 — 0.1 1.5 4.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.1 2.0 5.0 A3.0
D026 — 5.1 21 31 A 2.3 A/D Current (Note 1, Note 3), no
conversion in progress
— 5.7 23 33 A 3.0
— 6.1 25 35 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.