Datasheet

 2004-2014 Microchip Technology Inc. DS20001906D-page 3
MCP102/103/121/131
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings†
V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0V
Input current (V
DD
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Output current (RST
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 mA
Rated Rise Time of V
DD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100V/µs
All inputs and outputs (except RST) w.r.t. V
SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to (V
DD
+1.0V)
RST
output w.r.t. V
SS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.6V to 13.5V
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to + 150°C
Ambient temperature with power applied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to + 125°C
Maximum Junction temperature with power applied. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
ESD protection on all pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ³ 2 kV
† Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at those or any other conditions above those indicated in the
operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
DC CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, all limits are specified for: V
DD
= 1V to 5.5V, R
PU
= 100 k (MCP121 only),
T
A
= -40°C to +125°C.
Parameters Sym. Min. Typ. Max. Units Conditions
Operating Voltage Range V
DD
1.0 — 5.5 V
Specified V
DD
Value to RST low V
DD
1.0 — V I
RST
=10µA, V
RST
<0.2V
Operating Current
MCP102,
MCP103,
MCP121
I
DD
— < 1 1.75 µA Reset Power-up Timer (t
RPU
) Inactive
— — 20.0 µA Reset Power-up Timer (t
RPU
) Active
MCP131 I
DD
—<11.75µAV
DD
>V
TRIP
and Reset Power-up
Timer (t
RPU
) Inactive
——75µAV
DD
<V
TRIP
and Reset Power-up
Timer (t
RPU
) Inactive (Note 3)
— — 90 µA Reset Power-up Timer (t
RPU
) Active
(Note 4)
Note 1: Trip point is ±1.5% from typical value.
2: Trip point is ±2.5% from typical value.
3: RST
output is forced low. There is a current through the internal pull-up resistor.
4: This includes the current through the internal pull-up resistor and the reset power-up timer.
5: This specification allows this device to be used in PIC
®
microcontroller applications that require In-Circuit Serial
Programming™ (ICSP™) (see device-specific programming specifications for voltage requirements). This specification
DOES NOT allow a continuous high voltage to be present on the open-drain output pin (V
OUT
). The total time that the
V
OUT
pin can be above the maximum device operational voltage (5.5V) is 100s. Current into the V
OUT
pin should be
limited to 2 mA and it is recommended that the device operational temperature be maintained between 0°C to 70°C
(+25°C preferred). For additional information, please refer to Figure 2-33.
6: This parameter is established by characterization and not 100% tested.