Datasheet
Table Of Contents
- PICkit™ Serial Analyzer User's Guide
- Trademarks
- Table of Contents
- Chapter 1. PICkit™ Serial Analyzer Overview
- 1.1 Introduction
- 1.2 Highlights
- 1.3 PICkit™ Serial Analyzer Contents
- 1.4 PICkit™ Serial Analyzer Development System
- 1.5 PICkit™ Serial Analyzer Hardware
- 1.6 PICkit™ Serial Analyzer Software
- Chapter 2. Getting Started
- 2.1 Introduction
- 2.2 Highlights
- 2.3 Installing the PICkit™ Serial Analyzer Software
- 2.4 Connecting the PICkit™ Serial Analyzer to the PC
- 2.5 Connecting the PICkit™ Serial Analyzer to the 28-Pin Demo Board
- 2.6 Starting the PICkit™ Serial Analyzer Program
- 2.7 Running the 28-Pin Demo I2C™ Demonstration Program
- 2.8 I2C™ Communications – Basic Operations
- 2.9 28-Pin Demo I2C™ Source Code and Firmware
- Chapter 3. PICkit™ Serial Analyzer PC Program
- 3.1 Introduction
- 3.2 Highlights
- 3.3 Installing the PICkit™ Serial Analyzer Software
- 3.4 Starting the Program
- 3.5 Configuration Wizard
- 3.6 Main Window
- 3.7 Serial Communications Modes
- Chapter 4. I2C™ Master Communications
- 4.1 Introduction
- 4.2 Highlights
- 4.3 PICkit Serial Pin Assignments
- 4.4 Selecting Communications Mode
- 4.5 Configuring I2C Communications Mode
- 4.6 Communications: Basic Operations
- 4.7 Script Builder
- 4.8 Script Execute
- Chapter 5. I2C™ Slave Communications
- 5.1 Introduction
- 5.2 Highlights
- 5.3 PICkit Serial Pin Assignments
- 5.4 Selecting Communications Mode
- 5.5 Configuring I2C Slave Communications Mode
- 5.6 Communications: Basic Operations
- 5.7 Communications: Profile Generator
- Chapter 6. Lin Communications
- 6.1 Introduction
- 6.2 Highlights
- 6.3 PICkit Serial Pin Assignments
- 6.4 Selecting Communications Mode
- 6.5 Configuring Lin Slave Communications Mode
- 6.6 Communications: Basic Operations
- Chapter 7. SPI and Microwire Master Communications
- 7.1 Introduction
- 7.2 Highlights
- 7.3 PICkit™ Serial Analyzer Pin Assignments
- 7.4 Selecting Communications Mode
- 7.5 Configurating SPI Communications Mode
- 7.6 Communications: Basic Operations
- 7.7 Script Builder
- 7.8 Script Execute
- Chapter 8. USART Asynchronous Communications
- 8.1 Introduction
- 8.2 Highlights
- 8.3 PICkit Serial Pin Assignments
- 8.4 Selecting Communications Mode
- 8.5 Configuring USART Asynchronous Communications Mode
- 8.6 Communications: Basic Operations
- 8.7 Script Builder
- 8.8 Script Execute
- Chapter 9. USART Master Synchronous Communications
- 9.1 Introduction
- 9.2 Highlights
- 9.3 PICkit Serial Pin Assignments
- 9.4 Selecting Communications Mode
- 9.5 Configuring USART Synchronous Master Communications Mode
- 9.6 Communications: Basic Operations
- 9.7 Script Builder
- 9.8 Script Execute
- Chapter 10. User Defined Templates
- 10.1 Introduction
- 10.2 Highlights
- 10.3 Creating and Using Templates
- 10.4 My Templates
- 10.5 Graphing Data
- Chapter 11. PICkit™ Serial Analyzer Firmware
- 11.1 Introduction
- 11.2 Highlights
- 11.3 Overview
- 11.4 Exec
- 11.5 Comm
- 11.6 I2CM Communications
- 11.7 I2CS Communications
- 11.8 SPI Communications
- 11.9 USART Communications
- 11.10 LIN Communications
- Chapter 12. PICkit™ Serial Analyzer DLL
- 12.1 Introduction
- 12.2 Overview
- Chapter 13. Troubleshooting
- 13.1 Introduction
- 13.2 Frequently Asked Questions
- Appendix A. PICkit Serial Analyzer Schematics
- A.1 Introduction
- Appendix B. 28-Pin Demo Board I2C™ Demonstration Firmware
- B.1 Introduction
- B.2 Highlights
- B.3 Hardware
- B.4 Firmware
- B.5 I2C Communications
- B.6 Slave Devices
- B.7 Functions
- Worldwide Sales
PICkit™ Serial Analyzer User’s Guide
DS51647C-page 28 © 2009 Microchip Technology Inc.
4.4 SELECTING COMMUNICATIONS MODE
The I
2
C Master Communications mode is selected from the Configuration Wizard or
menu bar.
Configuration Wizard – Select PICkit Serial Analyzer > Run Configuration Wizard
from the menu bar
Menu Bar – Select PICkit Serial Analyzer > Select Communications Mode > I
2
C
Master
4.5 CONFIGURING I
2
C COMMUNICATIONS MODE
Once the communications mode has been selected, it is configured from the Configu-
ration Wizard or menu bar.
Configuration Wizard – Select PICkit Serial Analyzer > Run Configuration Wizard
from the menu bar
Menu Bar – Select PICkit Serial Analyzer > Configure Communications Mode
The Configure Mode window will open. Depending on the view selected, the Basic
View (Figure 4-1) displays a minimum choice of configurations commands. The
Advanced View (Figure 4-2) displays an extended choice of configuration commands.
Save the configuration by clicking on the Save Changes button.
FIGURE 4-1: I
2
C™ CONFIGURE COMMUNICATIONS MODE – BASIC VIEW
OPTIONS
• Enable Event Markers – Enable event markers
• Enable Time Markers – Enable time-stamp to accompany all event markers
• Enable Pullups – Enable internal 2.2 kΩ pull-ups on SDA and SCL communication
lines
VOLTAGE
• PICkit Serial will power my device – Select the check box if the PICkit Serial will
power the target device. The target can be powered at 5 V
DC or a user selectable
variable voltage.
CAUTION
Even though the voltage can be set as low as 0 VDC, it is up to the user to verify the
required operating voltage of the target device.