Datasheet
Table Of Contents
- Features
- 1. Ordering Information
- 2. Pinout/Block Diagram
- 3. Overview
- 4. Resources
- 5. Capacitive touch sensing
- 6. AVR CPU
- 7. Memories
- 8. DMAC – Direct Memory Access Controller
- 9. Event System
- 10. System Clock and Clock options
- 10.1 Features
- 10.2 Overview
- 10.3 Clock Sources
- 10.3.1 32kHz Ultra Low Power Internal Oscillator
- 10.3.2 32.768kHz Calibrated Internal Oscillator
- 10.3.3 32.768kHz Crystal Oscillator
- 10.3.4 0.4 - 16MHz Crystal Oscillator
- 10.3.5 2MHz Run-time Calibrated Internal Oscillator
- 10.3.6 32MHz Run-time Calibrated Internal Oscillator
- 10.3.7 External Clock Sources
- 10.3.8 PLL with 1x-31x Multiplication Factor
- 11. Power Management and Sleep Modes
- 12. System Control and Reset
- 13. WDT – Watchdog Timer
- 14. Interrupts and Programmable Multilevel Interrupt Controller
- 15. I/O Ports
- 16. TC0/1 – 16-bit Timer/Counter Type 0 and 1
- 17. TC2 - Timer/Counter Type 2
- 18. AWeX – Advanced Waveform Extension
- 19. Hi-Res – High Resolution Extension
- 20. RTC – 16-bit Real-Time Counter
- 21. USB – Universal Serial Bus Interface
- 22. TWI – Two-Wire Interface
- 23. SPI – Serial Peripheral Interface
- 24. USART
- 25. IRCOM – IR Communication Module
- 26. AES and DES Crypto Engine
- 27. CRC – Cyclic Redundancy Check Generator
- 28. ADC – 12-bit Analog to Digital Converter
- 29. DAC – 12-bit Digital to Analog Converter
- 30. AC – Analog Comparator
- 31. Programming and Debugging
- 32. Pinout and Pin Functions
- 33. Peripheral Module Address Map
- 34. Instruction Set Summary
- 35. Packaging information
- 36. Electrical Characteristics
- 36.1 ATxmega16A4U
- 36.1.1 Absolute Maximum Ratings
- 36.1.2 General Operating Ratings
- 36.1.3 Current consumption
- 36.1.4 Wake-up time from sleep modes
- 36.1.5 I/O Pin Characteristics
- 36.1.6 ADC characteristics
- 36.1.7 DAC Characteristics
- 36.1.8 Analog Comparator Characteristics
- 36.1.9 Bandgap and Internal 1.0V Reference Characteristics
- 36.1.10 Brownout Detection Characteristics
- 36.1.11 External Reset Characteristics
- 36.1.12 Power-on Reset Characteristics
- 36.1.13 Flash and EEPROM Memory Characteristics
- 36.1.14 Clock and Oscillator Characteristics
- 36.1.14.1 Calibrated 32.768kHz Internal Oscillator characteristics
- 36.1.14.2 Calibrated 2MHz RC Internal Oscillator characteristics
- 36.1.14.3 Calibrated and tunable 32MHz internal oscillator characteristics
- 36.1.14.4 32kHz Internal ULP Oscillator characteristics
- 36.1.14.5 Internal Phase Locked Loop (PLL) characteristics
- 36.1.14.6 External clock characteristics
- 36.1.14.7 External 16MHz crystal oscillator and XOSC characteristic
- 36.1.14.8 External 32.768kHz crystal oscillator and TOSC characteristics
- 36.1.15 SPI Characteristics
- 36.1.16 Two-Wire Interface Characteristics
- 36.2 ATxmega32A4U
- 36.2.1 Absolute Maximum Ratings
- 36.2.2 General Operating Ratings
- 36.2.3 Current consumption
- 36.2.4 Wake-up time from sleep modes
- 36.2.5 I/O Pin Characteristics
- 36.2.6 ADC characteristics
- 36.2.7 DAC Characteristics
- 36.2.8 Analog Comparator Characteristics
- 36.2.9 Bandgap and Internal 1.0V Reference Characteristics
- 36.2.10 Brownout Detection Characteristics
- 36.2.11 External Reset Characteristics
- 36.2.12 Power-on Reset Characteristics
- 36.2.13 Flash and EEPROM Memory Characteristics
- 36.2.14 Clock and Oscillator Characteristics
- 36.2.14.1 Calibrated 32.768kHz Internal Oscillator characteristics
- 36.2.14.2 Calibrated 2MHz RC Internal Oscillator characteristics
- 36.2.14.3 Calibrated and tunable 32MHz internal oscillator characteristics
- 36.2.14.4 32kHz Internal ULP Oscillator characteristics
- 36.2.14.5 Internal Phase Locked Loop (PLL) characteristics
- 36.2.14.6 External clock characteristics
- 36.2.14.7 External 16MHz crystal oscillator and XOSC characteristic
- 36.2.14.8 External 32.768kHz crystal oscillator and TOSC characteristics
- 36.2.15 SPI Characteristics
- 36.2.16 Two-Wire Interface Characteristics
- 36.3 ATxmega64A4U
- 36.3.1 Absolute Maximum Ratings
- 36.3.2 General Operating Ratings
- 36.3.3 Current consumption
- 36.3.4 Wake-up time from sleep modes
- 36.3.5 I/O Pin Characteristics
- 36.3.6 ADC characteristics
- 36.3.7 DAC Characteristics
- 36.3.8 Analog Comparator Characteristics
- 36.3.9 Bandgap and Internal 1.0V Reference Characteristics
- 36.3.10 Brownout Detection Characteristics
- 36.3.11 External Reset Characteristics
- 36.3.12 Power-on Reset Characteristics
- 36.3.13 Flash and EEPROM Memory Characteristics
- 36.3.14 Clock and Oscillator Characteristics
- 36.3.14.1 Calibrated 32.768kHz Internal Oscillator characteristics
- 36.3.14.2 Calibrated 2MHz RC Internal Oscillator characteristics
- 36.3.14.3 Calibrated and tunable 32MHz internal oscillator characteristics
- 36.3.14.4 32kHz Internal ULP Oscillator characteristics
- 36.3.14.5 Internal Phase Locked Loop (PLL) characteristics
- 36.3.14.6 External clock characteristics
- 36.3.14.7 External 16MHz crystal oscillator and XOSC characteristic
- 36.3.14.8 External 32.768kHz crystal oscillator and TOSC characteristics
- 36.3.15 SPI Characteristics
- 36.3.16 Two-Wire Interface Characteristics
- 36.4 ATxmega128A4U
- 36.4.1 Absolute Maximum Ratings
- 36.4.2 General Operating Ratings
- 36.4.3 Current consumption
- 36.4.4 Wake-up time from sleep modes
- 36.4.5 I/O Pin Characteristics
- 36.4.6 ADC characteristics
- 36.4.7 DAC Characteristics
- 36.4.8 Analog Comparator Characteristics
- 36.4.9 Bandgap and Internal 1.0V Reference Characteristics
- 36.4.10 Brownout Detection Characteristics
- 36.4.11 External Reset Characteristics
- 36.4.12 Power-on Reset Characteristics
- 36.4.13 Flash and EEPROM Memory Characteristics
- 36.4.14 Clock and Oscillator Characteristics
- 36.4.14.1 Calibrated 32.768kHz Internal Oscillator characteristics
- 36.4.14.2 Calibrated 2MHz RC Internal Oscillator characteristics
- 36.4.14.3 Calibrated and tunable 32MHz internal oscillator characteristics
- 36.4.14.4 32kHz Internal ULP Oscillator characteristics
- 36.4.14.5 Internal Phase Locked Loop (PLL) characteristics
- 36.4.14.6 External clock characteristics
- 36.4.14.7 External 16MHz crystal oscillator and XOSC characteristic
- 36.4.14.8 External 32.768kHz crystal oscillator and TOSC characteristics
- 36.4.15 SPI Characteristics
- 36.4.16 Two-Wire Interface Characteristics
- 36.1 ATxmega16A4U
- 37. Typical Characteristics
- 37.1 ATxmega16A4U
- 37.1.1 Current consumption
- 37.1.2 I/O Pin Characteristics
- 37.1.3 ADC Characteristics
- 37.1.4 DAC Characteristics
- 37.1.5 Analog Comparator Characteristics
- 37.1.6 Internal 1.0V reference Characteristics
- 37.1.7 BOD Characteristics
- 37.1.8 External Reset Characteristics
- 37.1.9 Power-on Reset Characteristics
- 37.1.10 Oscillator Characteristics
- 37.1.11 Two-Wire Interface characteristics
- 37.1.12 PDI characteristics
- 37.2 ATxmega32A4U
- 37.2.1 Current consumption
- 37.2.2 I/O Pin Characteristics
- 37.2.3 ADC Characteristics
- 37.2.4 DAC Characteristics
- 37.2.5 Analog Comparator Characteristics
- 37.2.6 Internal 1.0V reference Characteristics
- 37.2.7 BOD Characteristics
- 37.2.8 External Reset Characteristics
- 37.2.9 Power-on Reset Characteristics
- 37.2.10 Oscillator Characteristics
- 37.2.11 Two-Wire Interface characteristics
- 37.2.12 PDI characteristics
- 37.3 ATxmega64A4U
- 37.3.1 Current consumption
- 37.3.2 I/O Pin Characteristics
- 37.3.3 ADC Characteristics
- 37.3.4 DAC Characteristics
- 37.3.5 Analog Comparator Characteristics
- 37.3.6 Internal 1.0V reference Characteristics
- 37.3.7 BOD Characteristics
- 37.3.8 External Reset Characteristics
- 37.3.9 Power-on Reset Characteristics
- 37.3.10 Oscillator Characteristics
- 37.3.11 Two-Wire Interface characteristics
- 37.3.12 PDI characteristics
- 37.4 ATxmega128A4U
- 37.4.1 Current consumption
- 37.4.2 I/O Pin Characteristics
- 37.4.3 ADC Characteristics
- 37.4.4 DAC Characteristics
- 37.4.5 Analog Comparator Characteristics
- 37.4.6 Internal 1.0V reference Characteristics
- 37.4.7 BOD Characteristics
- 37.4.8 External Reset Characteristics
- 37.4.9 Power-on Reset Characteristics
- 37.4.10 Oscillator Characteristics
- 37.4.11 Two-Wire Interface characteristics
- 37.4.12 PDI characteristics
- 37.1 ATxmega16A4U
- 38. Errata
- 39. Datasheet Revision History
- Table of Contents
64
XMEGA A4U [DATASHEET]
Atmel-8387H-AVR-ATxmega16A4U-34A4U-64A4U-128A4U-Datasheet_09/2014
RCALL k Relative Call Subroutine PC ← PC + k + 1 None 2 / 3
(1)
ICALL Indirect Call to (Z) PC(15:0)
PC(21:16)
←
←
Z,
0
None 2 / 3
(1)
EICALL Extended Indirect Call to (Z) PC(15:0)
PC(21:16)
←
←
Z,
EIND
None 3
(1)
CALL k call Subroutine PC ← k None 3 / 4
(1)
RET Subroutine Return PC ← STACK None 4 / 5
(1)
RETI Interrupt Return PC ← STACK I 4 / 5
(1)
CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1 / 2 / 3
CP Rd,Rr Compare Rd - Rr Z,C,N,V,S,H 1
CPC Rd,Rr Compare with Carry Rd - Rr - C Z,C,N,V,S,H 1
CPI Rd,K Compare with Immediate Rd - K Z,C,N,V,S,H 1
SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b) = 0) PC ← PC + 2 or 3 None 1 / 2 / 3
SBRS Rr, b Skip if Bit in Register Set if (Rr(b) = 1) PC ← PC + 2 or 3 None 1 / 2 / 3
SBIC A, b Skip if Bit in I/O Register Cleared if (I/O(A,b) = 0) PC ← PC + 2 or 3 None 2 / 3 / 4
SBIS A, b Skip if Bit in I/O Register Set If (I/O(A,b) =1) PC ← PC + 2 or 3 None 2 / 3 / 4
BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC ← PC + k + 1 None 1 / 2
BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC ← PC + k + 1 None 1 / 2
BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1 / 2
BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1 / 2
BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1 / 2
BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1 / 2
BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1 / 2
BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1 / 2
BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1 / 2
BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1 / 2
BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1 / 2
BRLT k Branch if Less Than, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1 / 2
BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1 / 2
BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1 / 2
BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1 / 2
BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1 / 2
BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1 / 2
BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1 / 2
BRIE k Branch if Interrupt Enabled if (I = 1) then PC ← PC + k + 1 None 1 / 2
BRID k Branch if Interrupt Disabled if (I = 0) then PC ← PC + k + 1 None 1 / 2
Data transfer instructions
MOV Rd, Rr Copy Register Rd ← Rr None 1
Mnemonic
s
Operand
s
Description Operation Flags
#Clock
s