Datasheet
Table Of Contents
- 1. Pin Configurations
- 2. Overview
- 2.1 Block Diagram
- 2.2 Comparison Between ATmega1281/2561 and ATmega640/1280/2560
- 2.3 Pin Descriptions
- 2.3.1 VCC
- 2.3.2 GND
- 2.3.3 Port A (PA7..PA0)
- 2.3.4 Port B (PB7..PB0)
- 2.3.5 Port C (PC7..PC0)
- 2.3.6 Port D (PD7..PD0)
- 2.3.7 Port E (PE7..PE0)
- 2.3.8 Port F (PF7..PF0)
- 2.3.9 Port G (PG5..PG0)
- 2.3.10 Port H (PH7..PH0)
- 2.3.11 Port J (PJ7..PJ0)
- 2.3.12 Port K (PK7..PK0)
- 2.3.13 Port L (PL7..PL0)
- 2.3.14 RESET
- 2.3.15 XTAL1
- 2.3.16 XTAL2
- 2.3.17 AVCC
- 2.3.18 AREF
- 3. Resources
- 4. About Code Examples
- 5. Data Retention
- 6. Capacitive touch sensing
- 7. AVR CPU Core
- 8. AVR Memories
- 9. External Memory Interface
- 10. System Clock and Clock Options
- 10.1 Overview
- 10.2 Clock Systems and their Distribution
- 10.3 Clock Sources
- 10.4 Low Power Crystal Oscillator
- 10.5 Full Swing Crystal Oscillator
- 10.6 Low Frequency Crystal Oscillator
- 10.7 Calibrated Internal RC Oscillator
- 10.8 128kHz Internal Oscillator
- 10.9 External Clock
- 10.10 Clock Output Buffer
- 10.11 Timer/Counter Oscillator
- 10.12 System Clock Prescaler
- 10.13 Register Description
- 11. Power Management and Sleep Modes
- 12. System Control and Reset
- 13. I/O-Ports
- 13.1 Introduction
- 13.2 Ports as General Digital I/O
- 13.3 Alternate Port Functions
- 13.3.1 Alternate Functions of Port A
- 13.3.2 Alternate Functions of Port B
- 13.3.3 Alternate Functions of Port C
- 13.3.4 Alternate Functions of Port D
- 13.3.5 Alternate Functions of Port E
- 13.3.6 Alternate Functions of Port F
- 13.3.7 Alternate Functions of Port G
- 13.3.8 Alternate Functions of Port H
- 13.3.9 Alternate Functions of Port J
- 13.3.10 Alternate Functions of Port K
- 13.3.11 Alternate Functions of Port L
- 13.4 Register Description for I/O-Ports
- 13.4.1 MCUCR – MCU Control Register
- 13.4.2 PORTA – Port A Data Register
- 13.4.3 DDRA – Port A Data Direction Register
- 13.4.4 PINA – Port A Input Pins Address
- 13.4.5 PORTB – Port B Data Register
- 13.4.6 DDRB – Port B Data Direction Register
- 13.4.7 PINB – Port B Input Pins Address
- 13.4.8 PORTC – Port C Data Register
- 13.4.9 DDRC – Port C Data Direction Register
- 13.4.10 PINC– Port C Input Pins Address
- 13.4.11 PORTD – Port D Data Register
- 13.4.12 DDRD – Port D Data Direction Register
- 13.4.13 PIND – Port D Input Pins Address
- 13.4.14 PORTE – Port E Data Register
- 13.4.15 DDRE – Port E Data Direction Register
- 13.4.16 PINE – Port E Input Pins Address
- 13.4.17 PORTF – Port F Data Register
- 13.4.18 DDRF – Port F Data Direction Register
- 13.4.19 PINF – Port F Input Pins Address
- 13.4.20 PORTG – Port G Data Register
- 13.4.21 DDRG – Port G Data Direction Register
- 13.4.22 PING – Port G Input Pins Address
- 13.4.23 PORTH – Port H Data Register
- 13.4.24 DDRH – Port H Data Direction Register
- 13.4.25 PINH – Port H Input Pins Address
- 13.4.26 PORTJ – Port J Data Register
- 13.4.27 DDRJ – Port J Data Direction Register
- 13.4.28 PINJ – Port J Input Pins Address
- 13.4.29 PORTK – Port K Data Register
- 13.4.30 DDRK – Port K Data Direction Register
- 13.4.31 PINK – Port K Input Pins Address
- 13.4.32 PORTL – Port L Data Register
- 13.4.33 DDRL – Port L Data Direction Register
- 13.4.34 PINL – Port L Input Pins Address
- 14. Interrupts
- 15. External Interrupts
- 15.1 Pin Change Interrupt Timing
- 15.2 Register Description
- 15.2.1 EICRA – External Interrupt Control Register A
- 15.2.2 EICRB – External Interrupt Control Register B
- 15.2.3 EIMSK – External Interrupt Mask Register
- 15.2.4 EIFR – External Interrupt Flag Register
- 15.2.5 PCICR – Pin Change Interrupt Control Register
- 15.2.6 PCIFR – Pin Change Interrupt Flag Register
- 15.2.7 PCMSK2 – Pin Change Mask Register 2
- 15.2.8 PCMSK1 – Pin Change Mask Register 1
- 15.2.9 PCMSK0 – Pin Change Mask Register 0
- 16. 8-bit Timer/Counter0 with PWM
- 16.1 Features
- 16.2 Overview
- 16.3 Timer/Counter Clock Sources
- 16.4 Counter Unit
- 16.5 Output Compare Unit
- 16.6 Compare Match Output Unit
- 16.7 Modes of Operation
- 16.8 Timer/Counter Timing Diagrams
- 16.9 Register Description
- 16.9.1 TCCR0A – Timer/Counter Control Register A
- 16.9.2 TCCR0B – Timer/Counter Control Register B
- 16.9.3 TCNT0 – Timer/Counter Register
- 16.9.4 OCR0A – Output Compare Register A
- 16.9.5 OCR0B – Output Compare Register B
- 16.9.6 TIMSK0 – Timer/Counter Interrupt Mask Register
- 16.9.7 TIFR0 – Timer/Counter 0 Interrupt Flag Register
- 17. 16-bit Timer/Counter (Timer/Counter 1, 3, 4, and 5)
- 17.1 Features
- 17.2 Overview
- 17.3 Accessing 16-bit Registers
- 17.4 Timer/Counter Clock Sources
- 17.5 Counter Unit
- 17.6 Input Capture Unit
- 17.7 Output Compare Units
- 17.8 Compare Match Output Unit
- 17.9 Modes of Operation
- 17.10 Timer/Counter Timing Diagrams
- 17.11 Register Description
- 17.11.1 TCCR1A – Timer/Counter 1 Control Register A
- 17.11.2 TCCR3A – Timer/Counter 3 Control Register A
- 17.11.3 TCCR4A – Timer/Counter 4 Control Register A
- 17.11.4 TCCR5A – Timer/Counter 5 Control Register A
- 17.11.5 TCCR1B – Timer/Counter 1 Control Register B
- 17.11.6 TCCR3B – Timer/Counter 3 Control Register B
- 17.11.7 TCCR4B – Timer/Counter 4 Control Register B
- 17.11.8 TCCR5B – Timer/Counter 5 Control Register B
- 17.11.9 TCCR1C – Timer/Counter 1 Control Register C
- 17.11.10 TCCR3C – Timer/Counter 3 Control Register C
- 17.11.11 TCCR4C – Timer/Counter 4 Control Register C
- 17.11.12 TCCR5C – Timer/Counter 5 Control Register C
- 17.11.13 TCNT1H and TCNT1L – Timer/Counter 1
- 17.11.14 TCNT3H and TCNT3L – Timer/Counter 3
- 17.11.15 TCNT4H and TCNT4L –Timer/Counter 4
- 17.11.16 TCNT5H and TCNT5L –Timer/Counter 5
- 17.11.17 OCR1AH and OCR1AL – Output Compare Register 1 A
- 17.11.18 OCR1BH and OCR1BL – Output Compare Register 1 B
- 17.11.19 OCR1CH and OCR1CL – Output Compare Register 1 C
- 17.11.20 OCR3AH and OCR3AL – Output Compare Register 3 A
- 17.11.21 OCR3BH and OCR3BL – Output Compare Register 3 B
- 17.11.22 OCR3CH and OCR3CL – Output Compare Register 3 C
- 17.11.23 OCR4AH and OCR4AL – Output Compare Register 4 A
- 17.11.24 OCR4BH and OCR4BL – Output Compare Register 4 B
- 17.11.25 OCR4CH and OCR4CL –Output Compare Register 4 C
- 17.11.26 OCR5AH and OCR5AL – Output Compare Register 5 A
- 17.11.27 OCR5BH and OCR5BL – Output Compare Register 5 B
- 17.11.28 OCR5CH and OCR5CL –Output Compare Register 5 C
- 17.11.29 ICR1H and ICR1L – Input Capture Register 1
- 17.11.30 ICR3H and ICR3L – Input Capture Register 3
- 17.11.31 ICR4H and ICR4L – Input Capture Register 4
- 17.11.32 ICR5H and ICR5L – Input Capture Register 5
- 17.11.33 TIMSK1 – Timer/Counter 1 Interrupt Mask Register
- 17.11.34 TIMSK3 – Timer/Counter 3 Interrupt Mask Register
- 17.11.35 TIMSK4 – Timer/Counter 4 Interrupt Mask Register
- 17.11.36 TIMSK5 – Timer/Counter 5 Interrupt Mask Register
- 17.11.37 TIFR1 – Timer/Counter1 Interrupt Flag Register
- 17.11.38 TIFR3 – Timer/Counter3 Interrupt Flag Register
- 17.11.39 TIFR4 – Timer/Counter4 Interrupt Flag Register
- 17.11.40 TIFR5 – Timer/Counter5 Interrupt Flag Register
- 18. Timer/Counter 0, 1, 3, 4, and 5 Prescaler
- 19. Output Compare Modulator (OCM1C0A)
- 20. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 20.1 Overview
- 20.2 Timer/Counter Clock Sources
- 20.3 Counter Unit
- 20.4 Modes of Operation
- 20.5 Output Compare Unit
- 20.6 Compare Match Output Unit
- 20.7 Timer/Counter Timing Diagrams
- 20.8 Asynchronous Operation of Timer/Counter2
- 20.9 Timer/Counter Prescaler
- 20.10 Register Description
- 20.10.1 TCCR2A –Timer/Counter Control Register A
- 20.10.2 TCCR2B – Timer/Counter Control Register B
- 20.10.3 TCNT2 – Timer/Counter Register
- 20.10.4 OCR2A – Output Compare Register A
- 20.10.5 OCR2B – Output Compare Register B
- 20.10.6 ASSR – Asynchronous Status Register
- 20.10.7 TIMSK2 – Timer/Counter2 Interrupt Mask Register
- 20.10.8 TIFR2 – Timer/Counter2 Interrupt Flag Register
- 20.10.9 GTCCR – General Timer/Counter Control Register
- 21. SPI – Serial Peripheral Interface
- 22. USART
- 22.1 Features
- 22.2 Overview
- 22.3 Clock Generation
- 22.4 Frame Formats
- 22.5 USART Initialization
- 22.6 Data Transmission – The USART Transmitter
- 22.7 Data Reception – The USART Receiver
- 22.8 Asynchronous Data Reception
- 22.9 Multi-processor Communication Mode
- 22.10 Register Description
- 22.11 Examples of Baud Rate Setting
- 23. USART in SPI Mode
- 24. 2-wire Serial Interface
- 25. AC – Analog Comparator
- 26. ADC – Analog to Digital Converter
- 26.1 Features
- 26.2 Operation
- 26.3 Starting a Conversion
- 26.4 Prescaling and Conversion Timing
- 26.5 Changing Channel or Reference Selection
- 26.6 ADC Noise Canceler
- 26.7 ADC Conversion Result
- 26.8 Register Description
- 26.8.1 ADMUX – ADC Multiplexer Selection Register
- 26.8.2 ADCSRB – ADC Control and Status Register B
- 26.8.3 ADCSRA – ADC Control and Status Register A
- 26.8.4 ADCL and ADCH – The ADC Data Register
- 26.8.5 ADCSRB – ADC Control and Status Register B
- 26.8.6 DIDR0 – Digital Input Disable Register 0
- 26.8.7 DIDR2 – Digital Input Disable Register 2
- 27. JTAG Interface and On-chip Debug System
- 28. IEEE 1149.1 (JTAG) Boundary-scan
- 29. Boot Loader Support – Read-While-Write Self-Programming
- 29.1 Features
- 29.2 Application and Boot Loader Flash Sections
- 29.3 Read-While-Write and No Read-While-Write Flash Sections
- 29.4 Boot Loader Lock Bits
- 29.5 Addressing the Flash During Self-Programming
- 29.6 Self-Programming the Flash
- 29.6.1 Performing Page Erase by SPM
- 29.6.2 Filling the Temporary Buffer (Page Loading)
- 29.6.3 Performing a Page Write
- 29.6.4 Using the SPM Interrupt
- 29.6.5 Consideration While Updating BLS
- 29.6.6 Prevent Reading the RWW Section During Self-Programming
- 29.6.7 Setting the Boot Loader Lock Bits by SPM
- 29.6.8 EEPROM Write Prevents Writing to SPMCSR
- 29.6.9 Reading the Fuse and Lock Bits from Software
- 29.6.10 Reading the Signature Row from Software
- 29.6.11 Preventing Flash Corruption
- 29.6.12 Programming Time for Flash when Using SPM
- 29.6.13 Simple Assembly Code Example for a Boot Loader
- 29.6.14 ATmega640 Boot Loader Parameters
- 29.6.15 ATmega1280/1281 Boot Loader Parameters
- 29.6.16 ATmega2560/2561 Boot Loader Parameters
- 29.7 Register Description
- 30. Memory Programming
- 30.1 Program And Data Memory Lock Bits
- 30.2 Fuse Bits
- 30.3 Signature Bytes
- 30.4 Calibration Byte
- 30.5 Page Size
- 30.6 Parallel Programming Parameters, Pin Mapping, and Commands
- 30.7 Parallel Programming
- 30.7.1 Enter Programming Mode
- 30.7.2 Considerations for Efficient Programming
- 30.7.3 Chip Erase
- 30.7.4 Programming the Flash
- 30.7.5 Programming the EEPROM
- 30.7.6 Reading the Flash
- 30.7.7 Reading the EEPROM
- 30.7.8 Programming the Fuse Low Bits
- 30.7.9 Programming the Fuse High Bits
- 30.7.10 Programming the Extended Fuse Bits
- 30.7.11 Programming the Lock Bits
- 30.7.12 Reading the Fuse and Lock Bits
- 30.7.13 Reading the Signature Bytes
- 30.7.14 Reading the Calibration Byte
- 30.7.15 Parallel Programming Characteristics
- 30.8 Serial Downloading
- 30.9 Programming via the JTAG Interface
- 30.9.1 Programming Specific JTAG Instructions
- 30.9.2 AVR_RESET (0xC)
- 30.9.3 PROG_ENABLE (0x4)
- 30.9.4 PROG_COMMANDS (0x5)
- 30.9.5 PROG_PAGELOAD (0x6)
- 30.9.6 PROG_PAGEREAD (0x7)
- 30.9.7 Data Registers
- 30.9.8 Reset Register
- 30.9.9 Programming Enable Register
- 30.9.10 Programming Command Register
- 30.9.11 Flash Data Byte Register
- 30.9.12 Programming Algorithm
- 30.9.13 Entering Programming Mode
- 30.9.14 Leaving Programming Mode
- 30.9.15 Performing Chip Erase
- 30.9.16 Programming the Flash
- 30.9.17 Reading the Flash
- 30.9.18 Programming the EEPROM
- 30.9.19 Reading the EEPROM
- 30.9.20 Programming the Fuses
- 30.9.21 Programming the Lock Bits
- 30.9.22 Reading the Fuses and Lock Bits
- 30.9.23 Reading the Signature Bytes
- 30.9.24 Reading the Calibration Byte
- 31. Electrical Characteristics
- 32. Typical Characteristics
- 32.1 Active Supply Current
- 32.2 Idle Supply Current
- 32.3 Power-down Supply Current
- 32.4 Power-save Supply Current
- 32.5 Standby Supply Current
- 32.6 Pin Pull-up
- 32.7 Pin Driver Strength
- 32.8 Pin Threshold and Hysteresis
- 32.9 BOD Threshold and Analog Comparator Offset
- 32.10 Internal Oscillator Speed
- 32.11 Current Consumption of Peripheral Units
- 32.12 Current Consumption in Reset and Reset Pulsewidth
- 33. Register Summary
- 34. Instruction Set Summary
- 35. Ordering Information
- 36. Packaging Information
- 37. Errata
- 37.1 ATmega640 rev. B
- 37.2 ATmega640 rev. A
- 37.3 ATmega1280 rev. B
- 37.4 ATmega1280 rev. A
- 37.5 ATmega1281 rev. B
- 37.6 ATmega1281 rev. A
- 37.7 ATmega2560 rev. F
- 37.8 ATmega2560 rev. E
- 37.9 ATmega2560 rev. D
- 37.10 ATmega2560 rev. C
- 37.11 ATmega2560 rev. B
- 37.12 ATmega2560 rev. A
- 37.13 ATmega2561 rev. F
- 37.14 ATmega2561 rev. E
- 37.15 ATmega2561 rev. D
- 37.16 ATmega2561 rev. C
- 37.17 ATmega2561 rev. B
- 37.18 ATmega2561 rev. A
- 38. Datasheet Revision History
- 38.1 Rev. 2549Q-02/2014
- 38.2 Rev. 2549P-10/2012
- 38.3 Rev. 2549O-05/2012
- 38.4 Rev. 2549N-05/2011
- 38.5 Rev. 2549M-09/2010
- 38.6 Rev. 2549L-08/07
- 38.7 Rev. 2549K-01/07
- 38.8 Rev. 2549J-09/06
- 38.9 Rev. 2549I-07/06
- 38.10 Rev. 2549H-06/06
- 38.11 Rev. 2549G-06/06
- 38.12 Rev. 2549F-04/06
- 38.13 Rev. 2549E-04/06
- 38.14 Rev. 2549D-12/05
- 38.15 Rev. 2549C-09/05
- 38.16 Rev. 2549B-05/05
- 38.17 Rev. 2549A-03/05
181
ATmega640/V-1280/V-1281/V-2560/V-2561/V [DATASHEET]
2549Q–AVR–02/2014
The clock source for Timer/Counter2 is named clk
T2S
. clk
T2S
is by default connected to the main system I/O clock
clk
IO
. By setting the AS2 bit in ASSR, Timer/Counter2 is asynchronously clocked from the TOSC1 pin. This
enables use of Timer/Counter2 as a Real Time Counter (RTC). When AS2 is set, pins TOSC1 and TOSC2 are dis-
connected from Port C. A crystal can then be connected between the TOSC1 and TOSC2 pins to serve as an
independent clock source for Timer/Counter2. The Oscillator is optimized for use with a 32.768kHz crystal. By set-
ting the EXCLK bit in the ASSR, a 32kHz external clock can be applied. See “ASSR – Asynchronous Status
Register” on page 187 for details.
For Timer/Counter2, the possible prescaled selections are: clk
T2S
/8, clk
T2S
/32, clk
T2S
/64, clk
T2S
/128, clk
T2S
/256, and
clk
T2S
/1024. Additionally, clk
T2S
as well as 0 (stop) may be selected. Setting the PSRASY bit in GTCCR resets the
prescaler. This allows the user to operate with a predictable prescaler.