Datasheet

ManualsBrandsMicrochip ManualsAVR MicrocontrollersAVR RISC Microcontroller Flash 64KB TQFP

131

132

133

134

135

136

137

138

139

140

Table Of Contents

1. Pin Configurations
2. Overview
- 2.1 Block Diagram
- 2.2 Comparison Between ATmega1281/2561 and ATmega640/1280/2560
- 2.3 Pin Descriptions
3. Resources
4. About Code Examples
5. Data Retention
6. Capacitive touch sensing
7. AVR CPU Core
- 7.1 Introduction
- 7.2 Architectural Overview
- 7.3 ALU – Arithmetic Logic Unit
- 7.4 Status Register
  - 7.4.1 SREG – AVR Status Register
- 7.5 General Purpose Register File
  - 7.5.1 The X-register, Y-register, and Z-register
- 7.6 Stack Pointer
  - 7.6.1 RAMPZ – Extended Z-pointer Register for ELPM/SPM
  - 7.6.2 EIND – Extended Indirect Register
- 7.7 Instruction Execution Timing
- 7.8 Reset and Interrupt Handling
  - 7.8.1 Interrupt Response Time
8. AVR Memories
- 8.1 In-System Reprogrammable Flash Program Memory
- 8.2 SRAM Data Memory
  - 8.2.1 Data Memory Access Times
- 8.3 EEPROM Data Memory
  - 8.3.1 EEPROM Read/Write Access
  - 8.3.2 Preventing EEPROM Corruption
- 8.4 I/O Memory
  - 8.4.1 General Purpose I/O Registers
9. External Memory Interface
- 9.1 Overview
- 9.2 Register Description
  - 9.2.1 EEPROM registers
- 9.3 General Purpose registers
- 9.4 External Memory registers
  - 9.4.1 XMCRA – External Memory Control Register A
  - 9.4.2 XMCRB – External Memory Control Register B
10. System Clock and Clock Options
- 10.1 Overview
- 10.2 Clock Systems and their Distribution
- 10.3 Clock Sources
  - 10.3.1 Default Clock Source
  - 10.3.2 Clock Start-up Sequence
- 10.4 Low Power Crystal Oscillator
- 10.5 Full Swing Crystal Oscillator
- 10.6 Low Frequency Crystal Oscillator
- 10.7 Calibrated Internal RC Oscillator
- 10.8 128kHz Internal Oscillator
- 10.9 External Clock
- 10.10 Clock Output Buffer
- 10.11 Timer/Counter Oscillator
- 10.12 System Clock Prescaler
- 10.13 Register Description
  - 10.13.1 OSCCAL – Oscillator Calibration Register
  - 10.13.2 CLKPR – Clock Prescale Register
11. Power Management and Sleep Modes
- 11.1 Sleep Modes
- 11.2 Idle Mode
- 11.3 ADC Noise Reduction Mode
- 11.4 Power-down Mode
- 11.5 Power-save Mode
- 11.6 Standby Mode
- 11.7 Extended Standby Mode
- 11.8 Power Reduction Register
- 11.9 Minimizing Power Consumption
- 11.10 Register Description
12. System Control and Reset
- 12.1 Resetting the AVR
- 12.2 Reset Sources
- 12.3 Internal Voltage Reference
  - 12.3.1 Voltage Reference Enable Signals and Start-up Time
- 12.4 Watchdog Timer
  - 12.4.1 Features
  - 12.4.2 Overview
- 12.5 Register Description
  - 12.5.1 MCUSR – MCU Status Register
  - 12.5.2 WDTCSR – Watchdog Timer Control Register
13. I/O-Ports
- 13.1 Introduction
- 13.2 Ports as General Digital I/O
- 13.3 Alternate Port Functions
- 13.4 Register Description for I/O-Ports
14. Interrupts
- 14.1 Interrupt Vectors in ATmega640/1280/1281/2560/2561
- 14.2 Reset and Interrupt Vector placement
- 14.3 Moving Interrupts Between Application and Boot Section
- 14.4 Register Description
  - 14.4.1 MCUCR – MCU Control Register
15. External Interrupts
- 15.1 Pin Change Interrupt Timing
- 15.2 Register Description
16. 8-bit Timer/Counter0 with PWM
- 16.1 Features
- 16.2 Overview
  - 16.2.1 Registers
  - 16.2.2 Definitions
- 16.3 Timer/Counter Clock Sources
- 16.4 Counter Unit
- 16.5 Output Compare Unit
- 16.6 Compare Match Output Unit
  - 16.6.1 Compare Output Mode and Waveform Generation
- 16.7 Modes of Operation
- 16.8 Timer/Counter Timing Diagrams
- 16.9 Register Description
17. 16-bit Timer/Counter (Timer/Counter 1, 3, 4, and 5)
- 17.1 Features
- 17.2 Overview
  - 17.2.1 Registers
  - 17.2.2 Definitions
- 17.3 Accessing 16-bit Registers
  - 17.3.1 Reusing the Temporary High Byte Register
- 17.4 Timer/Counter Clock Sources
- 17.5 Counter Unit
- 17.6 Input Capture Unit
- 17.7 Output Compare Units
- 17.8 Compare Match Output Unit
  - 17.8.1 Compare Output Mode and Waveform Generation
- 17.9 Modes of Operation
- 17.10 Timer/Counter Timing Diagrams
- 17.11 Register Description
18. Timer/Counter 0, 1, 3, 4, and 5 Prescaler
- 18.1 Internal Clock Source
- 18.2 Prescaler Reset
- 18.3 External Clock Source
- 18.4 Register Description
  - 18.4.1 GTCCR – General Timer/Counter Control Register
19. Output Compare Modulator (OCM1C0A)
- 19.1 Overview
- 19.2 Description
  - 19.2.1 Timing example
20. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 20.1 Overview
  - 20.1.1 Registers
  - 20.1.2 Definitions
- 20.2 Timer/Counter Clock Sources
- 20.3 Counter Unit
- 20.4 Modes of Operation
- 20.5 Output Compare Unit
- 20.6 Compare Match Output Unit
  - 20.6.1 Compare Output Mode and Waveform Generation
- 20.7 Timer/Counter Timing Diagrams
- 20.8 Asynchronous Operation of Timer/Counter2
- 20.9 Timer/Counter Prescaler
- 20.10 Register Description
21. SPI – Serial Peripheral Interface
- 21.1 SS Pin Functionality
- 21.2 Register Description
22. USART
- 22.1 Features
- 22.2 Overview
- 22.3 Clock Generation
- 22.4 Frame Formats
  - 22.4.1 Parity Bit Calculation
- 22.5 USART Initialization
- 22.6 Data Transmission – The USART Transmitter
- 22.7 Data Reception – The USART Receiver
- 22.8 Asynchronous Data Reception
- 22.9 Multi-processor Communication Mode
  - 22.9.1 Using MPCMn
- 22.10 Register Description
- 22.11 Examples of Baud Rate Setting
23. USART in SPI Mode
- 23.1 Overview
- 23.2 USART MSPIM vs. SPI
  - 23.2.1 Clock Generation
- 23.3 SPI Data Modes and Timing
- 23.4 Frame Formats
  - 23.4.1 USART MSPIM Initialization
- 23.5 Data Transfer
  - 23.5.1 Transmitter and Receiver Flags and Interrupts
  - 23.5.2 Disabling the Transmitter or Receiver
- 23.6 USART MSPIM Register Description
24. 2-wire Serial Interface
- 24.1 Features
- 24.2 2-wire Serial Interface Bus Definition
  - 24.2.1 TWI Terminology
  - 24.2.2 Electrical Interconnection
- 24.3 Data Transfer and Frame Format
- 24.4 Multi-master Bus Systems, Arbitration, and Synchronization
- 24.5 Overview of the TWI Module
- 24.6 Using the TWI
- 24.7 Transmission Modes
- 24.8 Multi-master Systems and Arbitration
- 24.9 Register Description
25. AC – Analog Comparator
- 25.1 Analog Comparator Multiplexed Input
- 25.2 Register Description
26. ADC – Analog to Digital Converter
- 26.1 Features
- 26.2 Operation
- 26.3 Starting a Conversion
- 26.4 Prescaling and Conversion Timing
  - 26.4.1 Differential Channels
- 26.5 Changing Channel or Reference Selection
  - 26.5.1 ADC Input Channels
  - 26.5.2 ADC Voltage Reference
- 26.6 ADC Noise Canceler
- 26.7 ADC Conversion Result
- 26.8 Register Description
27. JTAG Interface and On-chip Debug System
- 27.1 Features
- 27.2 Overview
- 27.3 TAP - Test Access Port
  - 27.3.1 TAP Controller
- 27.4 Using the Boundary-scan Chain
- 27.5 Using the On-chip Debug System
- 27.6 On-chip Debug Specific JTAG Instructions
- 27.7 Using the JTAG Programming Capabilities
- 27.8 Bibliography
- 27.9 On-chip Debug Related Register in I/O Memory
  - 27.9.1 OCDR – On-chip Debug Register
28. IEEE 1149.1 (JTAG) Boundary-scan
- 28.1 Features
- 28.2 System Overview
- 28.3 Data Registers
- 28.4 Boundary-scan Specific JTAG Instructions
- 28.5 Boundary-scan Chain
  - 28.5.1 Scanning the Digital Port Pins
  - 28.5.2 Scanning the RESET Pin
- 28.6 Boundary-scan Related Register in I/O Memory
  - 28.6.1 MCUCR – MCU Control Register
  - 28.6.2 MCUSR – MCU Status Register
- 28.7 ATmega640/1280/1281/2560/2561 Boundary-scan Order
- 28.8 Boundary-scan Description Language Files
29. Boot Loader Support – Read-While-Write Self-Programming
- 29.1 Features
- 29.2 Application and Boot Loader Flash Sections
  - 29.2.1 Application Section
  - 29.2.2 BLS – Boot Loader Section
- 29.3 Read-While-Write and No Read-While-Write Flash Sections
  - 29.3.1 RWW – Read-While-Write Section
  - 29.3.2 NRWW – No Read-While-Write Section
- 29.4 Boot Loader Lock Bits
  - 29.4.1 Entering the Boot Loader Program
- 29.5 Addressing the Flash During Self-Programming
- 29.6 Self-Programming the Flash
- 29.7 Register Description
  - 29.7.1 SPMCSR – Store Program Memory Control and Status Register
30. Memory Programming
- 30.1 Program And Data Memory Lock Bits
- 30.2 Fuse Bits
  - 30.2.1 Latching of Fuses
- 30.3 Signature Bytes
- 30.4 Calibration Byte
- 30.5 Page Size
- 30.6 Parallel Programming Parameters, Pin Mapping, and Commands
  - 30.6.1 Signal Names
- 30.7 Parallel Programming
- 30.8 Serial Downloading
- 30.9 Programming via the JTAG Interface
31. Electrical Characteristics
- 31.1 DC Characteristics
- 31.2 Speed Grades
  - 31.2.1 8MHz
  - 31.2.2 16MHz
- 31.3 Clock Characteristics
  - 31.3.1 Calibrated Internal RC Oscillator Accuracy
  - 31.3.2 External Clock Drive Waveforms
- 31.4 External Clock Drive
- 31.5 System and Reset Characteristics
  - 31.5.1 Standard Power-On Reset
  - 31.5.2 Enhanced Power-On Reset
- 31.6 2-wire Serial Interface Characteristics
- 31.7 SPI Timing Characteristics
- 31.8 ADC Characteristics – Preliminary Data
- 31.9 External Data Memory Timing
32. Typical Characteristics
- 32.1 Active Supply Current
- 32.2 Idle Supply Current
  - 32.2.1 Supply Current of IO modules
- 32.3 Power-down Supply Current
- 32.4 Power-save Supply Current
- 32.5 Standby Supply Current
- 32.6 Pin Pull-up
- 32.7 Pin Driver Strength
- 32.8 Pin Threshold and Hysteresis
- 32.9 BOD Threshold and Analog Comparator Offset
- 32.10 Internal Oscillator Speed
- 32.11 Current Consumption of Peripheral Units
- 32.12 Current Consumption in Reset and Reset Pulsewidth
33. Register Summary
34. Instruction Set Summary
35. Ordering Information
- 35.1 ATmega640
- 35.2 ATmega1280
- 35.3 ATmega1281
- 35.4 ATmega2560
- 35.5 ATmega2561
36. Packaging Information
- 36.1 100A
- 36.2 100C1
- 36.3 64A
- 36.4 64M2
37. Errata
- 37.1 ATmega640 rev. B
- 37.2 ATmega640 rev. A
- 37.3 ATmega1280 rev. B
- 37.4 ATmega1280 rev. A
- 37.5 ATmega1281 rev. B
- 37.6 ATmega1281 rev. A
- 37.7 ATmega2560 rev. F
- 37.8 ATmega2560 rev. E
- 37.9 ATmega2560 rev. D
- 37.10 ATmega2560 rev. C
- 37.11 ATmega2560 rev. B
- 37.12 ATmega2560 rev. A
- 37.13 ATmega2561 rev. F
- 37.14 ATmega2561 rev. E
- 37.15 ATmega2561 rev. D
- 37.16 ATmega2561 rev. C
- 37.17 ATmega2561 rev. B
- 37.18 ATmega2561 rev. A
38. Datasheet Revision History
- 38.1 Rev. 2549Q-02/2014
- 38.2 Rev. 2549P-10/2012
- 38.3 Rev. 2549O-05/2012
- 38.4 Rev. 2549N-05/2011
- 38.5 Rev. 2549M-09/2010
- 38.6 Rev. 2549L-08/07
- 38.7 Rev. 2549K-01/07
- 38.8 Rev. 2549J-09/06
- 38.9 Rev. 2549I-07/06
- 38.10 Rev. 2549H-06/06
- 38.11 Rev. 2549G-06/06
- 38.12 Rev. 2549F-04/06
- 38.13 Rev. 2549E-04/06
- 38.14 Rev. 2549D-12/05
- 38.15 Rev. 2549C-09/05
- 38.16 Rev. 2549B-05/05
- 38.17 Rev. 2549A-03/05

131

ATmega640/V-1280/V-1281/V-2560/V-2561/V [DATASHEET]

2549Q–AVR–02/2014

16.9.6 TIMSK0 – Timer/Counter Interrupt Mask Register

• Bits 7:3, 0 – Res: Reserved Bits

These bits are reserved bits and will always read as zero.

• Bit 2 – OCIE0B: Timer/Counter Output Compare Match B Interrupt Enable

When the OCIE0B bit is written to one, and the I-bit in the Status Register is set, the Timer/Counter Compare

Match B interrupt is enabled. The corresponding interrupt is executed if a Compare Match in Timer/Counter occurs,

that is, when the OCF0B bit is set in the Timer/Counter Interrupt Flag Register – TIFR0.

• Bit 1 – OCIE0A: Timer/Counter0 Output Compare Match A Interrupt Enable

When the OCIE0A bit is written to one, and the I-bit in the Status Register is set, the Timer/Counter0 Compare

Match A interrupt is enabled. The corresponding interrupt is executed if a Compare Match in Timer/Counter0

occurs, that is, when the OCF0A bit is set in the Timer/Counter 0 Interrupt Flag Register – TIFR0.

• Bit 0 – TOIE0: Timer/Counter0 Overflow Interrupt Enable

When the TOIE0 bit is written to one, and the I-bit in the Status Register is set, the Timer/Counter0 Overflow inter-

rupt is enabled. The corresponding interrupt is executed if an overflow in Timer/Counter0 occurs, that is, when the

TOV0 bit is set in the Timer/Counter 0 Interrupt Flag Register – TIFR0.

16.9.7 TIFR0 – Timer/Counter 0 Interrupt Flag Register

• Bits 7:3, 0 – Res: Reserved Bits

These bits are reserved bits and will always read as zero.

• Bit 2 – OCF0B: Timer/Counter 0 Output Compare B Match Flag

The OCF0B bit is set when a Compare Match occurs between the Timer/Counter and the data in OCR0B – Output

Compare Register0 B. OCF0B is cleared by hardware when executing the corresponding interrupt handling vector.

Alternatively, OCF0B is cleared by writing a logic one to the flag. When the I-bit in SREG, OCIE0B (Timer/Counter

Compare B Match Interrupt Enable), and OCF0B are set, the Timer/Counter Compare Match Interrupt is executed.

• Bit 1 – OCF0A: Timer/Counter 0 Output Compare A Match Flag

The OCF0A bit is set when a Compare Match occurs between the Timer/Counter0 and the data in OCR0A – Out-

put Compare Register0. OCF0A is cleared by hardware when executing the corresponding interrupt handling

vector. Alternatively, OCF0A is cleared by writing a logic one to the flag. When the I-bit in SREG, OCIE0A

(Timer/Counter0 Compare Match Interrupt Enable), and OCF0A are set, the Timer/Counter0 Compare Match Inter-

rupt is executed.

• Bit 0 – TOV0: Timer/Counter0 Overflow Flag

The bit TOV0 is set when an overflow occurs in Timer/Counter0. TOV0 is cleared by hardware when executing the

corresponding interrupt handling vector. Alternatively, TOV0 is cleared by writing a logic one to the flag. When the

Bit 76543 2 10

(0x6E) –––––OCIE0BOCIE0ATOIE0TIMSK0

Read/WriteRRRRRR/W R/W R/W

Initial Value00000 0 00

Bit 76543210

0x15 (0x35) –––––OCF0BOCF0A

TOV0 TIFR0

Read/WriteRRRRRR/W R/W R/W

Initial Value00000000