Datasheet

ATmega164A/PA/324A/PA/644A/PA/1284/P
 2018 Microchip Technology Inc. Data Sheet Complete DS40002070A-page 224
When SLA+W have been transmitted and an acknowledgement bit has been received, TWINT is set again and
a number of status codes in TWSR are possible. Possible status codes in Master mode are 0x18, 0x20, or 0x38.
The appropriate action to be taken for each of these status codes is detailed in Table 21-3 on page 224.
When SLA+W has been successfully transmitted, a data packet should be transmitted. This is done by writing
the data byte to TWDR. TWDR must only be written when TWINT is high. If not, the access will be discarded,
and the Write Collision bit (TWWC) will be set in the TWCR Register. After updating TWDR, the TWINT bit
should be cleared (by writing it to one) to continue the transfer. This is accomplished by writing the following
value to TWCR:
This scheme is repeated until the last byte has been sent and the transfer is ended by generating a STOP
condition or a repeated START condition. A STOP condition is generated by writing the following value to
TWCR:
A REPEATED START condition is generated by writing the following value to TWCR:
After a repeated START condition (state 0x10) the two-wire Serial Interface can access the same Slave again,
or a new Slave without transmitting a STOP condition. Repeated START enables the Master to switch between
Slaves, Master Transmitter mode and Master Receiver mode without losing control of the bus.
TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE
value 1
X00X10 X
TWCR TWINT
TWEA TWSTA TWSTO TWWC TWEN – TWIE
value 1
X01X10 X
TWCR TWINT
TWEA TWSTA TWSTO TWWC TWEN – TWIE
value 1
X10X10 X
Table 21-3. Status codes for Master Transmitter mode
Status Code
(TWSR)
Prescaler Bits
are 0
Status of the two-wire Serial
Bus and two-wire Serial Inter-
face Hardware
Application Software Response
Next Action Taken by TWI Hardware
To/from TWDR To TWCR
STA STO TWIN
T
TWE
A
0x08 A START condition has been
transmitted
Load SLA+W 0 0 1 X SLA+W will be transmitted;
ACK or NOT ACK will be received
0x10 A repeated START condition
has been transmitted
Load SLA+W or
Load SLA+R
0
0
0
0
1
1
X
X
SLA+W will be transmitted;
ACK or NOT ACK will be received
SLA+R will be transmitted;
Logic will switch to Master Receiver mode
0x18 SLA+W has been transmitted;
ACK has been received
Load data byte or
No TWDR action or
No TWDR action or
No TWDR action
0
1
0
1
0
0
1
1
1
1
1
1
X
X
X
X
Data byte will be transmitted and ACK or NOT ACK will
be received
Repeated START will be transmitted
STOP condition will be transmitted and
TWSTO Flag will be reset
STOP condition followed by a START condition will be
transmitted and TWSTO Flag will be reset
0x20 SLA+W has been transmitted;
NOT ACK has been received
Load data byte or
No TWDR action or
No TWDR action or
No TWDR action
0
1
0
1
0
0
1
1
1
1
1
1
X
X
X
X
Data byte will be transmitted and ACK or NOT ACK will
be received
Repeated START will be transmitted
STOP condition will be transmitted and
TWSTO Flag will be reset
STOP condition followed by a START condition will be
transmitted and TWSTO Flag will be reset