Datasheet

ManualsBrandsMicrochip ManualsCPLDsHigh Performance EE PLD 166MHz 5.5V PDIP

Features

• Industry-standard Architecture

– Low-cost, Easy-to-use Software Tools

• High-speed, Electrically Erasable Programmable Logic Devices

– 5ns Maximum Pin-to-pin Delay

• Latch Feature Holds Inputs to Previous Logic States

• Pin-controlled Standby Power (10µA Typical)

• Advanced Flash Technology

– Reprogrammable

– 100% Tested

• High-reliability CMOS Process

– 20-year Data Retention

– 100 Erase/Write Cycles

– 2,000V ESD Protection

– 200mA Latch-up Immunity

• Dual Inline and Surface Mount Packages in Standard Pinouts

• PCI-compliant

• Green Package Options (Pb/Halide-free/RoHS Compliant) Available

• Full Military, Commercial and Industrial Temperature Ranges

• Backward-Compatible with Atmel ATF22V10B(Q) and Atmel AT22V10(L)

• Applications Include Glue Logic for 5.0V Systems, DMA Control, State Machine

Control, Graphics Processing

1. Description

The Atmel

ATF22V10C is a high-performance CMOS (electrically erasable) pro-

grammable logic device (PLD) that utilizes proven electrically erasable Flash memory

technology from Atmel. Speeds down to 5ns and power dissipation as low as 10µA

(typical) are offered. All speed ranges are specified over the full 5V ± 10% range for

military and industrial temperature ranges, and 5V ± 5% for commercial temperature

ranges.

Several low-power options allow selection of the best solution for various types of

power-limited applications. Each of these options significantly reduces total system

power and enhances system reliability.

High-performance

Electrically

Erasable

Programmable

Logic Device

Atmel ATF22V10C

Atmel ATF22V10CQ

See separate datasheet for

the Atmel ATF22V10C(Q)Z

0735U–PLD–7/10

Summary of content (22 pages)

PAGE 1
Features • Industry-standard Architecture • • • • • • • • • • • – Low-cost, Easy-to-use Software Tools High-speed, Electrically Erasable Programmable Logic Devices – 5ns Maximum Pin-to-pin Delay Latch Feature Holds Inputs to Previous Logic States Pin-controlled Standby Power (10µA Typical) Advanced Flash Technology – Reprogrammable – 100% Tested High-reliability CMOS Process – 20-year Data Retention – 100 Erase/Write Cycles – 2,000V ESD Protection – 200mA Latch-up Immunity Dual Inline and Surface Mount P
PAGE 2
Figure 1-1. 2. Logic Diagram Pin Configurations Table 2-1. Pin Configurations (All Pinouts Top View) Pin Name Function CLK Clock IN Logic Inputs I/O Bi-directional Buffers GND Ground VCC +5V Supply PD Power-down Figure 2-1.
PAGE 3
Atmel ATF22V10C(Q) 3. Absolute Maximum Ratings* Temperature under Bias ................. -55°C to +125°C *NOTICE: Storage Temperature...................... -65°C to +150°C Voltage on Any Pin with Respect to Ground...........................-2.0V to +7.0V(1) Voltage on Input Pins with Respect to Ground during Programming ......................-2.0V to +14.0V(1) Note: Programming Voltage with Respect to Ground.........................-2.0V to +14.0V(1) 4.
PAGE 4
.1 DC Characteristics Symbol Parameter Condition IIL Input or I/O Low Leakage Current IIH Input or I/O High Leakage Current ICC ICC2 Power Supply Current, Standby Clocked Power Supply Current Min Typ Max Units 0 VIN VIL (Max) -10.0 µA 3.5 VIN VCC 10.0 µA C-5, 7, 10 Com. 85.0 130.0 mA C-10 Ind. 90.0 140.0 mA C-15 Ind. 65.0 115.0 mA CQ-15 Ind. 35.0 70.0 mA C-5, 7, 10 Com. 150.0 mA C-10 Ind., Mil. 160.0 mA C-15 Ind. 125 mA C-15 Mil. 160.
PAGE 5
Atmel ATF22V10C(Q) 4.3 AC Characteristics(1) -5 -7 -10 -15 Symbol Parameter Min Max Min Max Min Max Min Max Units tPD Input or Feedback to Combinatorial Output 1.0 5.0 3.0 7.5 3.0 10.0 3.0 15.0 ns tCO Clock to Output 1.0 4.0 2.0 4.5(2) 2.0 6.5 2.0 8.0 ns tCF Clock to Feedback 2.5 ns tS Input or Feedback Setup Time tH Hold Time 2.5 2.5 3.0 3.5 0 0 4.5 10.0 ns 0 0 ns 90.0 55.5 MHz External Feedback 1/(tS + tCO) 142.
PAGE 6
4.4 Power-down AC Characteristics(1)(2)(3) -5 -7 Min Max Min -15 Symbol Parameter Min tIVDH Valid Input before PD High 5.0 7.5 10.0 15.0 ns tGVDH Valid OE before PD High 0 0 0 0 ns tCVDH Valid Clock before PD High 0 0 0 tDHIX Input Don’t Care after PD High 5.0 7.0 10.0 15.0 ns tDHGX OE Don’t Care after PD High 5.0 7.0 10.0 15.0 ns tDHCX Clock Don’t Care after PD High 5.0 7.0 10.0 15.0 ns tDLIV PD Low to Valid Input 5.0 7.5 10.0 15.
PAGE 7
Atmel ATF22V10C(Q) 4.7 Power-up Reset The registers in the Atmel® ATF22V10Cs are designed to reset during power-up. At a point delayed slightly from VCC crossing VRST, all registers will be reset to the low state. The output state will depend on the polarity of the output buffer. This feature is critical for state machine initialization. However, due to the asynchronous nature of reset and the uncertainty of how VCC actually rises in the system, the following conditions are required: 1.
PAGE 8
. Input and I/O Pin-keeper Circuits The Atmel® ATF22V10C contains internal input and I/O pin-keeper circuits. These circuits allow each ATF22V10C pin to hold its previous value even when it is not being driven by an external source or by the device’s output buffer. This helps to ensure that all logic array inputs are at known valid logic levels. This reduces system power by preventing pins from floating to indeterminate levels.
PAGE 9
Atmel ATF22V10C(Q) 9. Power-down Mode The Atmel® ATF22V10C includes an optional pin-controlled power-down feature. When this mode is enabled, the PD pin acts as the power-down pin (Pin 4 on the DIP/SOIC packages and Pin 5 on the PLCC package). When the PD pin is high, the device supply current is reduced to less than 100mA. During power-down, all output data and internal logic states are latched and held. Therefore, all registered and combinatorial output data remain valid.
PAGE 10
11.
PAGE 11
Atmel ATF22V10C(Q) ATMEL ATF22V10C/CQ NORMALIZED ICC VS. TEMPERATURE ATMEL ATF22V10C/CQ SUPPLY CURRENT VS. SUPPLY VOLTAGE (TA = 25°C) 1.1 140.0 120.0 I CC (mA) NORMALIZED ICC C-5, -7, -10 100.0 C-15 80.0 CQ-15 60.0 40.0 20.0 1.0 0.9 0.8 0.0 4.50 4.75 5.00 5.25 -40.0 5.50 25.0 ATMEL ATF22V10C/CQ SUPPLY CURRENT VS. INPUT FREQUENCY (VCC = 5V, TA = 25°C) ATMEL ATF22V10C/CQ OUTPUT SOURCE CURRENT VS. OUTPUT VOLTAGE (VCC = 5V, TA = 25°C) C-5, 7, 10 80.0 IOH (mA) C-15 CQ-15 40.0 0.0 0.
PAGE 12
ATMEL ATF22V10C/CQ NORMALIZED TCO VS. TEMPERATURE ATMEL ATF22V10C/CQ NORMALIZED TPD VS. VCC 1.1 NORMALIZED TCO NORMALIZED TPD 1.2 1.1 1.0 0.9 0.8 1.0 0.9 0.8 4.50 4.75 5.00 5.25 5.50 -40.0 0.0 SUPPLY VOLTAGE (V) 1.1 NORMALIZED TSU NORMALIZED TCO 1.3 1.2 1.1 1.0 0.9 0.8 1.0 0.9 0.8 4.50 4.75 5.00 5.25 5.50 -40.0 0.0 SUPPLY VOLTAGE (V) 75.0 ATMEL ATF22V10C/CQ DELTA TPD VS. OUTPUT LOADING 8.0 DELTA TPD (ns) 1.2 NORMALIZED TSU 25.
PAGE 13
Atmel ATF22V10C(Q) ATMEL ATF22V10C/CQ DELTA TCO VS. OUTPUT LOADING ATMEL ATF22V10C/CQ DELTA TCO VS. NUMBER OF SWITCHING 0.0 8.0 DELTA TCO (ns) DELTA TCO (ns) 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 50 100 150 200 250 NUMBER OF OUTPUTS LOADING 300 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.
PAGE 14
12. Ordering Information 12.1 Atmel ATF22V10C(Q) Green Package Options (Pb/Halide-free/RoHS Compliant) tPD (ns) tS (ns) tCO (ns) 5 3 4 7.5 3.5 7.5 3.5 10 4.5 15 10 Ordering Code Package Operation Range ATF22V10C-5JX 28J Commercial (0C to 70C) 4.5 ATF22V10C-7PX ATF22V10C-7SX 24P3 24S Commercial (0C to 70C) 4.5 ATF22V10C-7JU 28J Industrial (-40°C to 85C) 6.
PAGE 15
Atmel ATF22V10C(Q) 13. Packaging Information 13.1 24D3 – CERDIP Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 D-9 Config A (Glass Sealed) 32.51(1.280) 31.50(1.240) PIN 1 7.87(0.310) 7.24(0.285) 27.94(1.100) REF 5.08(0.200) MAX 0.127(0.005) MIN SEATING PLANE 5.08(0.200) 3.18(0.125) 2.45(0.100)BSC 0.46(0.018) 0.20(0.008) 1.65(0.065) 1.14(0.045) 1.52(0.060) 0.38(0.015) 0.66(0.026) 0.36(0.014) 8.13(0.320) 7.37(0.290) 0º~ 15º REF 10.20(0.
PAGE 16
13.2 24P3 – PDIP D PIN 1 E1 A SEATING PLANE A1 L B B1 e E COMMON DIMENSIONS (Unit of Measure = mm) C eC eB Notes: 1. 2. This package conforms to JEDEC reference MS-001, Variation AF Dimensions D and E1 do not include mold Flash or Protrusion Mold Flash or Protrusion shall not exceed 0.25mm (0.010") MIN SYMBOL NOM MAX A – – 5.334 A1 0.381 – – D 31.623 – 32.131 E 7.620 – 8.255 E1 6.096 – 7.112 B 0.356 – 0.559 B1 1.270 – 1.651 L 2.921 – 3.810 C 0.203 – 0.
PAGE 17
Atmel ATF22V10C(Q) 13.3 24S – SOIC B D1 D PIN 1 ID PIN 1 e E A COMMON DIMENSIONS (Unit of Measure = mm) A1 0 8 L1 L SYMBOL MIN NOM MAX A – – 2.65 A1 0.10 – 0.30 D 10.00 – 10.65 D1 7.40 – 7.60 E 15.20 – 15.60 B 0.33 – 0.51 L 0.40 – 1.27 L1 0.23 – 0.32 e NOTE 1.27 BSC 06/17/2002 Package Drawing Contact: packagedrawings@atmel.com TITLE 24S, 24-lead (0.300" body) Plastic Gull Wing Small Outline (SOIC) DRAWING NO. REV.
PAGE 18
13.4 24X – TSSOP Dimensions in Millimeter and (Inches)* JEDEC STANDARD MO-153 AD Controlling dimension: millimeters 0.30(0.012) 0.19(0.007) 4.48(0.176) 6.50(0.256) 4.30(0.169) 6.25(0.246) PIN 1 0.65(0.0256)BSC 7.90(0.311) 1.20(0.047)MAX 7.70(0.303) 0.15(0.006) 0.05(0.002) 0 0.20(0.008) 8 0.09(0.004) 0.75(0.030) 0.45(0.018) 04/11/2001 Package Drawing Contact: packagedrawings@atmel.com 18 TITLE 24X, 24-lead (4.4mm body width) Plastic Thin Shrink Small Outline Package (TSSOP) DRAWING NO. REV.
PAGE 19
Atmel ATF22V10C(Q) 13.5 28J – PLCC 1.14(0.045) X 45° PIN NO. 1 1.14(0.045) X 45° 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 E D2/E2 B1 B e A2 D1 A1 D A 0.51(0.020)MAX 45° MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AB 2. Dimensions D1 and E1 do not include mold protrusion Allowable protrusion is .010"(0.254mm) per side.
PAGE 20
13.6 28L – LCC Dimensions in Millimeters and (Inches). Controlling dimension: Inches. MIL-STD 1835 C-4 11.68(0.460) 11.23(0.442) 2.54(0.100) 2.16(0.085) 11.68(0.460) 11.23(0.442) PIN 1 2.41(0.095) 1.91(0.075) 1.40(0.055) 1.14(0.045) 1.91(0.075) 1.40(0.055) INDEX CORNER 0.635(0.025) X 45° 0.381(0.015) 0.305(0.012) RADIUS 0.178(0.007) 7.62(0.300) BSC 0.737(0.029) 0.533(0.021) 1.27(0.050) TYP 1.02(0.040) X 45° 7.62(0.300) BSC 2.16(0.085) 1.65(0.
PAGE 21
Atmel ATF22V10C(Q) 14. Revision History Doc. Rev. Date Comments 0735U 05/2010 Updated C-15 military device ICC limit Revised the maximum power supply current in PD mode for commercial- and industrial-grade devices from 100µA to 500µA and 100µA to 650µA maximum, respectively C-15 and CQ-15 Commercial part removed from Table 4-1. Removed Mil from ICC, C-15 (Ind.
PAGE 22
Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1) (408) 441-0311 Fax: (+1) (408) 487-2600 www.atmel.com Atmel Asia Limited Unit 01-5 & 16, 19F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg.