Datasheet

SAM9263 [DATASHEET]
Atmel-6249N-ATARM-SAM9263-Datasheet_14-Mar-16
374
3. When the instruction loaded at address 0x18 is executed, the program counter is loaded with the value read
in AIC_IVR. Reading the AIC_IVR has the following effects:
 Sets the current interrupt to be the pending and enabled interrupt with the highest priority. The current
level is the priority level of the current interrupt.
 De-asserts the nIRQ line on the processor. Even if vectoring is not used, AIC_IVR must be read in
order to de-assert nIRQ.
 Automatically clears the interrupt, if it has been programmed to be edge-triggered.
 Pushes the current level and the current interrupt number on to the stack.
 Returns the value written in the AIC_SVR corresponding to the current interrupt.
4. The previous step has the effect of branching to the corresponding interrupt service routine. This should start
by saving the link register (R14_irq) and SPSR_IRQ. The link register must be decremented by four when it
is saved if it is to be restored directly into the program counter at the end of the interrupt. For example, the
instruction SUB PC, LR, #4 may be used.
5. Further interrupts can then be unmasked by clearing the “I” bit in CPSR, allowing re-assertion of the nIRQ to
be taken into account by the core. This can happen if an interrupt with a higher priority than the current
interrupt occurs.
6. The interrupt handler can then proceed as required, saving the registers that will be used and restoring them
at the end. During this phase, an interrupt of higher priority than the current level will restart the sequence
from step 1.
Note: If the interrupt is programmed to be level sensitive, the source of the interrupt must be cleared during this phase.
7. The “I” bit in CPSR must be set in order to mask interrupts before exiting to ensure that the interrupt is
completed in an orderly manner.
8. The End of Interrupt Command Register (AIC_EOICR) must be written in order to indicate to the AIC that the
current interrupt is finished. This causes the current level to be popped from the stack, restoring the previous
current level if one exists on the stack. If another interrupt is pending, with lower or equal priority than the old
current level but with higher priority than the new current level, the nIRQ line is re-asserted, but the interrupt
sequence does not immediately start because the “I” bit is set in the core. SPSR_irq is restored. Finally, the
saved value of the link register is restored directly into the PC. This has the effect of returning from the
interrupt to whatever was being executed before, and of loading the CPSR with the stored SPSR, masking
or unmasking the interrupts depending on the state saved in SPSR_irq.
Note: The “I” bit in SPSR is significant. If it is set, it indicates that the ARM core was on the verge of masking an interrupt
when the mask instruction was interrupted. Hence, when SPSR is restored, the mask instruction is completed
(interrupt is masked).
28.7.4 Fast Interrupt
28.7.4.1 Fast Interrupt Source
The interrupt source 0 is the only source which can raise a fast interrupt request to the processor except if fast
forcing is used. The interrupt source 0 is generally connected to a FIQ pin of the product, either directly or through
a PIO Controller.
28.7.4.2 Fast Interrupt Control
The fast interrupt logic of the AIC has no priority controller. The mode of interrupt source 0 is programmed with the
AIC_SMR0 and the field PRIOR of this register is not used even if it reads what has been written. The field
SRCTYPE of AIC_SMR0 enables programming the fast interrupt source to be positive-edge triggered or negative-
edge triggered or high-level sensitive or low-level sensitive
Writing 0x1 in the AIC_IECR (Interrupt Enable Command Register) and AIC_IDCR (Interrupt Disable Command
Register) respectively enables and disables the fast interrupt. The bit 0 of AIC_IMR (Interrupt Mask Register)
indicates whether the fast interrupt is enabled or disabled.