Datasheet

SAM9261 [DATASHEET]
Atmel-6062O-ATARM-SAM9261-Datasheet_21-Jun-16
738
TC: Section 33.5.12 ”External Event/Trigger Conditions” on page 496 new text as follows:
“....(EEVT = 0), TIOB is no longer used as an output and the compare register B is not used
to generate waveforms and subsequently no IRQs.” Added note
(1)
to EEVT bit description
in Section 33.6.5 ”TC Channel Mode Register: Waveform Mode” on page 504
.
2704
MCI: Specified reset condition for DCRCE and DTOE bits in Section 34.10.10 “MCI Status
Register” on page 572.
2593
MCI: Update to Figure 34-9, “Write Functional Flow Diagram,” on page 558 in case of write
with PDC. Addition of Figure 34-10, “Multiple Write Functional Flow Diagram,” on
page 559.
2462
UHP: Corrected signal name and corrected ASB bus to ASB bus in Figure 35-1, “Block
Diagram,” on page 545 to UHPCK.
2924
LCDC: Corrected typos in signal names in Figure 37-4, “TFT Panel Timing, CLKMOD = 0,
VPW = 2, VBP = 2, VFP = 1,” on page 598.
2402
LCDC: Removed references to AHB and LCDC clock domains in Figure 37-1, “LCD
Macrocell Block Diagram,” on page 586.
2424
LCDC: Updated Section 37.9 ”Register Configuration Guide” on page 610. 2426
LCDC: Modified signal names throughout to be consistent with device: LCD_VSYNC
changed to LCDVSYNC, LCD_HSYNC changed to LCDHSYNC, LCD_PCLK changed to
LCDDOTCK, LCD_DVAL changed to LCDDEN, LCD_CC changed to LCDCC.
Removed all references to LCD_MOD and LCD_PWR as these signals are not bonded in
the device: Table 37-1, “I/O Lines Description,” on page 587, Section 37.5.2.3 ”Timegen”
on page 595, Section 37.5.2.4 ”Display” on page 600, Section 37.7 ”Configuration
Sequence” on page 607, Section 37.9.1 ”STN Mode Example” on page 610, Section 37.9.2
”TFT Mode Example” on page 610, Table 37.10, “LCD Controller (LCDC) User Interface,”
on page 611 and removed LCDMOD Toggle Rate Value Register.
2763
Electrical Characteristics: Corrected typ value for R
PULLUP
in Table 38-2, “DC
Characteristics,” on page 635.
2457
Electrical Characteristics:
New Table 38-5, “Processor Clock Waveform Parameters,” on page 638.
Deleted table Master Clock Characteristics, page 638.
New data for t
ST
in Table 38-7, “32 kHz Oscillator Characteristics,” on page 639.
New data in Table 38-8, “Main Oscillator Characteristics,” on page 640, I
DDST
, P
ON
, I
DDON
,
C
LEXT
. New max values for t
ST
.
New Table 38-9, “Crystal Characteristics,” on page 641.
New data on pull-ups in Table 38-11, “USB Transceiver Electrical Parameters,” on
page 642.
Deleted section “Applicable Conditions and Derating Data” and figures “Derating Curve for
Different Operating Temperatures”, “Derating Curve for Different Core Supply Voltages”
and “ Derating Curve for Different IO Supply Voltages”.
New tables with SMC and SDRAMC timings in Section 38.7 ”EBI Timings” on page 644.
New figures for SMC timings Figure 38-3, “SMC Signals for NCS Controlled Accesses,” on
page 647 and Figure 38-4, “SMC Signals for NRD and NWR Controlled Accesses,” on
page 648.
In Table 38-19, “SDRAMC Signals,” on page 649, some SDRAMx derating values changed
from positive to negative.
2619
Doc. Rev.
6062D
Date
14-Apr-06 Comments (Continued)
Change
Request
Reference