Datasheet

ManualsBrandsMicrochip ManualsAVR MicrocontrollersAVR RISC Microcontroller 8bit 64KB TQFP

321

322

323

324

325

326

327

328

329

330

Table Of Contents

1. Description
- 1.1 Comparison Between AT90CAN32, AT90CAN64 and AT90CAN128
- 1.2 Part Description
- 1.3 Disclaimer
- 1.4 Block Diagram
- 1.5 Pin Configurations
- 1.6 Pin Descriptions
2. About Code Examples
3. AVR CPU Core
- 3.1 Introduction
- 3.2 Architectural Overview
- 3.3 ALU - Arithmetic Logic Unit
- 3.4 Status Register
- 3.5 General Purpose Register File
- 3.6 Stack Pointer
- 3.7 Instruction Execution Timing
- 3.8 Reset and Interrupt Handling
4. Memories
- 4.1 In-System Reprogrammable Flash Program Memory
- 4.2 SRAM Data Memory
- 4.3 EEPROM Data Memory
- 4.4 I/O Memory
- 4.5 External Memory Interface
- 4.6 General Purpose I/O Registers
5. System Clock
- 5.1 Clock Systems and their Distribution
- 5.2 Clock Sources
- 5.3 Default Clock Source
- 5.4 Crystal Oscillator
- 5.5 Low-frequency Crystal Oscillator
- 5.6 Calibrated Internal RC Oscillator
- 5.7 External Clock
- 5.8 Clock Output Buffer
- 5.9 Timer/Counter2 Oscillator
- 5.10 System Clock Prescaler
6. Power Management and Sleep Modes
- 6.1 Idle Mode
- 6.2 ADC Noise Reduction Mode
- 6.3 Power-down Mode
- 6.4 Power-save Mode
- 6.5 Standby Mode
- 6.6 Minimizing Power Consumption
7. System Control and Reset
- 7.1 Reset
- 7.2 Internal Voltage Reference
- 7.3 Watchdog Timer
- 7.4 Timed Sequences for Changing the Configuration of the Watchdog Timer
8. Interrupts
- 8.1 Interrupt Vectors in AT90CAN32/64/128
- 8.2 Moving Interrupts Between Application and Boot Space
9. I/O-Ports
- 9.1 Introduction
- 9.2 Ports as General Digital I/O
- 9.3 Alternate Port Functions
- 9.4 Register Description for I/O-Ports
10. External Interrupts
- 10.1 External Interrupt Register Description
11. Timer/Counter3/1/0 Prescalers
- 11.1 Overview
- 11.2 Timer/Counter0/1/3 Prescalers Register Description
12. 8-bit Timer/Counter0 with PWM
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Output Compare Unit
- 12.6 Compare Match Output Unit
- 12.7 Modes of Operation
- 12.8 Timer/Counter Timing Diagrams
- 12.9 8-bit Timer/Counter Register Description
13. 16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- 13.1 Features
- 13.2 Overview
- 13.3 Accessing 16-bit Registers
- 13.4 Timer/Counter Clock Sources
- 13.5 Counter Unit
- 13.6 Input Capture Unit
- 13.7 Output Compare Units
- 13.8 Compare Match Output Unit
- 13.9 Modes of Operation
- 13.10 Timer/Counter Timing Diagrams
- 13.11 16-bit Timer/Counter Register Description
14. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 14.1 Features
- 14.2 Overview
- 14.3 Timer/Counter Clock Sources
- 14.4 Counter Unit
- 14.5 Output Compare Unit
- 14.6 Compare Match Output Unit
- 14.7 Modes of Operation
- 14.8 Timer/Counter Timing Diagrams
- 14.9 8-bit Timer/Counter Register Description
- 14.10 Asynchronous operation of the Timer/Counter2
- 14.11 Timer/Counter2 Prescaler
15. Output Compare Modulator - OCM
- 15.1 Overview
- 15.2 Description
16. Serial Peripheral Interface - SPI
- 16.1 Features
- 16.2 SS Pin Functionality
- 16.3 Data Modes
17. USART (USART0 and USART1)
- 17.1 Features
- 17.2 Overview
- 17.3 Dual USART
- 17.4 Clock Generation
- 17.5 Serial Frame
- 17.6 USART Initialization
- 17.7 Data Transmission - USART Transmitter
- 17.8 Data Reception - USART Receiver
- 17.9 Asynchronous Data Reception
- 17.10 Multi-processor Communication Mode
- 17.11 USART Register Description
- 17.12 Examples of Baud Rate Setting
18. Two-wire Serial Interface
- 18.1 Features
- 18.2 Two-wire Serial Interface Bus Definition
- 18.3 Data Transfer and Frame Format
- 18.4 Multi-master Bus Systems, Arbitration and Synchronization
- 18.5 Overview of the TWI Module
- 18.6 TWI Register Description
- 18.7 Using the TWI
- 18.8 Transmission Modes
- 18.9 Multi-master Systems and Arbitration
19. Controller Area Network - CAN
- 19.1 Features
- 19.2 CAN Protocol
- 19.3 CAN Controller
- 19.4 CAN Channel
- 19.5 Message Objects
- 19.6 CAN Timer
- 19.7 Error Management
- 19.8 Interrupts
- 19.9 CAN Register Description
- 19.10 General CAN Registers
- 19.11 MOb Registers
- 19.12 Examples of CAN Baud Rate Setting
20. Analog Comparator
- 20.1 Overview
- 20.2 Analog Comparator Register Description
- 20.3 Analog Comparator Multiplexed Input
21. Analog to Digital Converter - ADC
- 21.1 Features
- 21.2 Operation
- 21.3 Starting a Conversion
- 21.4 Prescaling and Conversion Timing
- 21.5 Changing Channel or Reference Selection
- 21.6 ADC Noise Canceler
- 21.7 ADC Conversion Result
- 21.8 ADC Register Description
22. JTAG Interface and On-chip Debug System
- 22.1 Features
- 22.2 Overview
- 22.3 Test Access Port - TAP
- 22.4 TAP Controller
- 22.5 Using the Boundary-scan Chain
- 22.6 Using the On-chip Debug System
- 22.7 On-chip Debug Specific JTAG Instructions
- 22.8 On-chip Debug Related Register in I/O Memory
- 22.9 Using the JTAG Programming Capabilities
- 22.10 Bibliography
23. Boundary-scan IEEE 1149.1 (JTAG)
- 23.1 Features
- 23.2 System Overview
- 23.3 Data Registers
- 23.4 Boundary-scan Specific JTAG Instructions
- 23.5 Boundary-scan Related Register in I/O Memory
- 23.6 Boundary-scan Chain
- 23.7 AT90CAN32/64/128 Boundary-scan Order
- 23.8 Boundary-scan Description Language Files
24. Boot Loader Support - Read-While-Write Self-Programming
- 24.1 Features
- 24.2 Application and Boot Loader Flash Sections
- 24.3 Read-While-Write and No Read-While-Write Flash Sections
- 24.4 Boot Loader Lock Bits
- 24.5 Entering the Boot Loader Program
- 24.6 Addressing the Flash During Self-Programming
- 24.7 Self-Programming the Flash
25. Memory Programming
- 25.1 Program and Data Memory Lock Bits
- 25.2 Fuse Bits
- 25.3 Signature Bytes
- 25.4 Calibration Byte
- 25.5 Parallel Programming Overview
- 25.6 Parallel Programming
- 25.7 SPI Serial Programming Overview
- 25.8 SPI Serial Programming
- 25.9 JTAG Programming Overview
26. Electrical Characteristics (1)
- 26.1 Absolute Maximum Ratings*
- 26.2 DC Characteristics
- 26.3 External Clock Drive Characteristics
- 26.4 Maximum Speed vs. VCC
- 26.5 Two-wire Serial Interface Characteristics
- 26.6 SPI Timing Characteristics
- 26.7 CAN Physical Layer Characteristics
- 26.8 ADC Characteristics
- 26.9 External Data Memory Characteristics
- 26.10 Parallel Programming Characteristics
27. Decoupling Capacitors
28. AT90CAN32/64/128 Typical Characteristics
- 28.1 Active Supply Current
- 28.2 Idle Supply Current
- 28.3 Power-down Supply Current
- 28.4 Power-save Supply Current
- 28.5 Standby Supply Current
- 28.6 Pin Pull-up
- 28.7 Pin Driver Strength
- 28.8 Pin Thresholds and Hysteresis
- 28.9 BOD Thresholds and Analog Comparator Offset
- 28.10 Internal Oscillator Speed
- 28.11 Current Consumption of Peripheral Units
- 28.12 Current Consumption in Reset and Reset Pulse Width
29. Register Summary
30. Instruction Set Summary
31. Ordering Information
32. Packaging Information
- 32.1 TQFP64
- 32.2 QFN64
33. Errata
- 33.1 Errata Summary
- 33.2 Errata Description
34. Datasheet Revision History for AT90CAN32/64/128
- 34.1 Changes from 7679G - 03/08 to 7679H - 08/08
- 34.2 Changes from 7679F - 11/07 to 7679G - 03/08
- 34.3 Changes from 7679E - 07/07 to 7679F - 11/07
- 34.4 Changes from 7679D - 02/07 to 7679E - 07/07
- 34.5 Changes from 7679C - 01/07 to 7679D - 02/07
- 34.6 Changes from 7679B - 11/06 to 7679C - 01/07
- 34.7 Changes from 7679A - 10/06 to 7679B - 11/06
- 34.8 Document Creation

321

7679H–CAN–08/08

AT90CAN32/64/128

24. Boot Loader Support – Read-While-Write Self-Programming

The Boot Loader Support provides a real Read-While-Write Self-Programming mechanism for

downloading and uploading program code by the MCU itself. This feature allows flexible applica-

tion software updates controlled by the MCU using a Flash-resident Boot Loader program. The

Boot Loader program can use any available data interface and associated protocol to read code

and write (program) that code into the Flash memory, or read the code from the program mem-

ory. The program code within the Boot Loader section has the capability to write into the entire

Flash, including the Boot Loader memory. The Boot Loader can thus even modify itself, and it

can also erase itself from the code if the feature is not needed anymore. The size of the Boot

Loader memory is configurable with fuses and the Boot Loader has two separate sets of Boot

Lock bits which can be set independently. This gives the user a unique flexibility to select differ-

ent levels of protection.

24.1 Features

• Read-While-Write Self-Programming

• Flexible Boot Memory Size

• High Security (Separate Boot Lock Bits for a Flexible Protection)

• Separate Fuse to Select Reset Vector

• Optimized Page

(1)

Size

• Code Efficient Algorithm

• Efficient Read-Modify-Write Support

Note: 1. A page is a section in the Flash consisting of several bytes (see Table 25-11 on page 341)

used during programming. The page organization does not affect normal operation.

24.2 Application and Boot Loader Flash Sections

The Flash memory is organized in two main sections, the Application section and the Boot

Loader section (see Figure 24-2). The size of the different sections is configured by the

BOOTSZ Fuses as shown in Table 24-6 on page 334 and Figure 24-2. These two sections can

have different level of protection since they have different sets of Lock bits.

24.2.1 AS - Application Section

The Application section is the section of the Flash that is used for storing the application code.

The protection level for the Application section can be selected by the application Boot Lock bits

(BLB02 and BLB01 bits), see Table 24-2 on page 325. The Application section can never store

any Boot Loader code since the SPM instruction is disabled when executed from the Application

section.

24.2.2 BLS – Boot Loader Section

While the Application section is used for storing the application code, the The Boot Loader soft-

ware must be located in the BLS since the SPM instruction can initiate a programming when

executing from the BLS only. The SPM instruction can access the entire Flash, including the

BLS itself. The protection level for the Boot Loader section can be selected by the Boot Loader

Lock bits (BLB12 and BLB11 bits), see Table 24-3 on page 325.

24.3 Read-While-Write and No Read-While-Write Flash Sections

Whether the CPU supports Read-While-Write or if the CPU is halted during a Boot Loader soft-

ware update is dependent on which address that is being programmed. In addition to the two