Datasheet

ManualsBrandsMicrochip ManualsAVR MicrocontrollersAVR RISC Microcontroller 8bit 64KB TQFP

231

232

233

234

235

236

237

238

239

240

Table Of Contents

1. Description
- 1.1 Comparison Between AT90CAN32, AT90CAN64 and AT90CAN128
- 1.2 Part Description
- 1.3 Disclaimer
- 1.4 Block Diagram
- 1.5 Pin Configurations
- 1.6 Pin Descriptions
2. About Code Examples
3. AVR CPU Core
- 3.1 Introduction
- 3.2 Architectural Overview
- 3.3 ALU - Arithmetic Logic Unit
- 3.4 Status Register
- 3.5 General Purpose Register File
- 3.6 Stack Pointer
- 3.7 Instruction Execution Timing
- 3.8 Reset and Interrupt Handling
4. Memories
- 4.1 In-System Reprogrammable Flash Program Memory
- 4.2 SRAM Data Memory
- 4.3 EEPROM Data Memory
- 4.4 I/O Memory
- 4.5 External Memory Interface
- 4.6 General Purpose I/O Registers
5. System Clock
- 5.1 Clock Systems and their Distribution
- 5.2 Clock Sources
- 5.3 Default Clock Source
- 5.4 Crystal Oscillator
- 5.5 Low-frequency Crystal Oscillator
- 5.6 Calibrated Internal RC Oscillator
- 5.7 External Clock
- 5.8 Clock Output Buffer
- 5.9 Timer/Counter2 Oscillator
- 5.10 System Clock Prescaler
6. Power Management and Sleep Modes
- 6.1 Idle Mode
- 6.2 ADC Noise Reduction Mode
- 6.3 Power-down Mode
- 6.4 Power-save Mode
- 6.5 Standby Mode
- 6.6 Minimizing Power Consumption
7. System Control and Reset
- 7.1 Reset
- 7.2 Internal Voltage Reference
- 7.3 Watchdog Timer
- 7.4 Timed Sequences for Changing the Configuration of the Watchdog Timer
8. Interrupts
- 8.1 Interrupt Vectors in AT90CAN32/64/128
- 8.2 Moving Interrupts Between Application and Boot Space
9. I/O-Ports
- 9.1 Introduction
- 9.2 Ports as General Digital I/O
- 9.3 Alternate Port Functions
- 9.4 Register Description for I/O-Ports
10. External Interrupts
- 10.1 External Interrupt Register Description
11. Timer/Counter3/1/0 Prescalers
- 11.1 Overview
- 11.2 Timer/Counter0/1/3 Prescalers Register Description
12. 8-bit Timer/Counter0 with PWM
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Output Compare Unit
- 12.6 Compare Match Output Unit
- 12.7 Modes of Operation
- 12.8 Timer/Counter Timing Diagrams
- 12.9 8-bit Timer/Counter Register Description
13. 16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- 13.1 Features
- 13.2 Overview
- 13.3 Accessing 16-bit Registers
- 13.4 Timer/Counter Clock Sources
- 13.5 Counter Unit
- 13.6 Input Capture Unit
- 13.7 Output Compare Units
- 13.8 Compare Match Output Unit
- 13.9 Modes of Operation
- 13.10 Timer/Counter Timing Diagrams
- 13.11 16-bit Timer/Counter Register Description
14. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 14.1 Features
- 14.2 Overview
- 14.3 Timer/Counter Clock Sources
- 14.4 Counter Unit
- 14.5 Output Compare Unit
- 14.6 Compare Match Output Unit
- 14.7 Modes of Operation
- 14.8 Timer/Counter Timing Diagrams
- 14.9 8-bit Timer/Counter Register Description
- 14.10 Asynchronous operation of the Timer/Counter2
- 14.11 Timer/Counter2 Prescaler
15. Output Compare Modulator - OCM
- 15.1 Overview
- 15.2 Description
16. Serial Peripheral Interface - SPI
- 16.1 Features
- 16.2 SS Pin Functionality
- 16.3 Data Modes
17. USART (USART0 and USART1)
- 17.1 Features
- 17.2 Overview
- 17.3 Dual USART
- 17.4 Clock Generation
- 17.5 Serial Frame
- 17.6 USART Initialization
- 17.7 Data Transmission - USART Transmitter
- 17.8 Data Reception - USART Receiver
- 17.9 Asynchronous Data Reception
- 17.10 Multi-processor Communication Mode
- 17.11 USART Register Description
- 17.12 Examples of Baud Rate Setting
18. Two-wire Serial Interface
- 18.1 Features
- 18.2 Two-wire Serial Interface Bus Definition
- 18.3 Data Transfer and Frame Format
- 18.4 Multi-master Bus Systems, Arbitration and Synchronization
- 18.5 Overview of the TWI Module
- 18.6 TWI Register Description
- 18.7 Using the TWI
- 18.8 Transmission Modes
- 18.9 Multi-master Systems and Arbitration
19. Controller Area Network - CAN
- 19.1 Features
- 19.2 CAN Protocol
- 19.3 CAN Controller
- 19.4 CAN Channel
- 19.5 Message Objects
- 19.6 CAN Timer
- 19.7 Error Management
- 19.8 Interrupts
- 19.9 CAN Register Description
- 19.10 General CAN Registers
- 19.11 MOb Registers
- 19.12 Examples of CAN Baud Rate Setting
20. Analog Comparator
- 20.1 Overview
- 20.2 Analog Comparator Register Description
- 20.3 Analog Comparator Multiplexed Input
21. Analog to Digital Converter - ADC
- 21.1 Features
- 21.2 Operation
- 21.3 Starting a Conversion
- 21.4 Prescaling and Conversion Timing
- 21.5 Changing Channel or Reference Selection
- 21.6 ADC Noise Canceler
- 21.7 ADC Conversion Result
- 21.8 ADC Register Description
22. JTAG Interface and On-chip Debug System
- 22.1 Features
- 22.2 Overview
- 22.3 Test Access Port - TAP
- 22.4 TAP Controller
- 22.5 Using the Boundary-scan Chain
- 22.6 Using the On-chip Debug System
- 22.7 On-chip Debug Specific JTAG Instructions
- 22.8 On-chip Debug Related Register in I/O Memory
- 22.9 Using the JTAG Programming Capabilities
- 22.10 Bibliography
23. Boundary-scan IEEE 1149.1 (JTAG)
- 23.1 Features
- 23.2 System Overview
- 23.3 Data Registers
- 23.4 Boundary-scan Specific JTAG Instructions
- 23.5 Boundary-scan Related Register in I/O Memory
- 23.6 Boundary-scan Chain
- 23.7 AT90CAN32/64/128 Boundary-scan Order
- 23.8 Boundary-scan Description Language Files
24. Boot Loader Support - Read-While-Write Self-Programming
- 24.1 Features
- 24.2 Application and Boot Loader Flash Sections
- 24.3 Read-While-Write and No Read-While-Write Flash Sections
- 24.4 Boot Loader Lock Bits
- 24.5 Entering the Boot Loader Program
- 24.6 Addressing the Flash During Self-Programming
- 24.7 Self-Programming the Flash
25. Memory Programming
- 25.1 Program and Data Memory Lock Bits
- 25.2 Fuse Bits
- 25.3 Signature Bytes
- 25.4 Calibration Byte
- 25.5 Parallel Programming Overview
- 25.6 Parallel Programming
- 25.7 SPI Serial Programming Overview
- 25.8 SPI Serial Programming
- 25.9 JTAG Programming Overview
26. Electrical Characteristics (1)
- 26.1 Absolute Maximum Ratings*
- 26.2 DC Characteristics
- 26.3 External Clock Drive Characteristics
- 26.4 Maximum Speed vs. VCC
- 26.5 Two-wire Serial Interface Characteristics
- 26.6 SPI Timing Characteristics
- 26.7 CAN Physical Layer Characteristics
- 26.8 ADC Characteristics
- 26.9 External Data Memory Characteristics
- 26.10 Parallel Programming Characteristics
27. Decoupling Capacitors
28. AT90CAN32/64/128 Typical Characteristics
- 28.1 Active Supply Current
- 28.2 Idle Supply Current
- 28.3 Power-down Supply Current
- 28.4 Power-save Supply Current
- 28.5 Standby Supply Current
- 28.6 Pin Pull-up
- 28.7 Pin Driver Strength
- 28.8 Pin Thresholds and Hysteresis
- 28.9 BOD Thresholds and Analog Comparator Offset
- 28.10 Internal Oscillator Speed
- 28.11 Current Consumption of Peripheral Units
- 28.12 Current Consumption in Reset and Reset Pulse Width
29. Register Summary
30. Instruction Set Summary
31. Ordering Information
32. Packaging Information
- 32.1 TQFP64
- 32.2 QFN64
33. Errata
- 33.1 Errata Summary
- 33.2 Errata Description
34. Datasheet Revision History for AT90CAN32/64/128
- 34.1 Changes from 7679G - 03/08 to 7679H - 08/08
- 34.2 Changes from 7679F - 11/07 to 7679G - 03/08
- 34.3 Changes from 7679E - 07/07 to 7679F - 11/07
- 34.4 Changes from 7679D - 02/07 to 7679E - 07/07
- 34.5 Changes from 7679C - 01/07 to 7679D - 02/07
- 34.6 Changes from 7679B - 11/06 to 7679C - 01/07
- 34.7 Changes from 7679A - 10/06 to 7679B - 11/06
- 34.8 Document Creation

236

7679H–CAN–08/08

AT90CAN32/64/128

19.2.2.2 CAN Extended Frame

Figure 19-2. CAN Extended Frames

A message in the CAN extended frame format is likely the same as a message in CAN standard

frame format. The difference is the length of the identifier used. The identifier is made up of the

existing 11-bit identifier (base identifier) and an 18-bit extension (identifier extension). The dis-

tinction between CAN standard frame format and CAN extended frame format is made by using

the IDE bit which is transmitted as dominant in case of a frame in CAN standard frame format,

and transmitted as recessive in the other case.

19.2.2.3 Format Co-existence

As the two formats have to co-exist on one bus, it is laid down which message has higher priority

on the bus in the case of bus access collision with different formats and the same identifier /

base identifier: The message in CAN standard frame format always has priority over the mes-

sage in extended format.

There are three different types of CAN modules available:

– 2.0A - Considers 29 bit ID as an error

– 2.0B Passive - Ignores 29 bit ID messages

– 2.0B Active - Handles both 11 and 29 bit ID Messages

19.2.3 CAN Bit Timing

To ensure correct sampling up to the last bit, a CAN node needs to re-synchronize throughout

the entire frame. This is done at the beginning of each message with the falling edge SOF and

on each recessive to dominant edge.

19.2.3.1 Bit Construction

One CAN bit time is specified as four non-overlapping time segments. Each segment is con-

structed from an integer multiple of the Time Quantum. The Time Quantum or TQ is the smallest

discrete timing resolution used by a CAN node.

11-bit base identifier

IDT28..18

Interframe

Space

CRC

del.

ACK

del.

15-bit CRC

0 - 8 bytes

SOF

SRR

IDE ACK

7 bits

Intermission

3 bits

Bus Idle Bus Idle

(Indefinite)

Arbitration

Field

Arbitration

Field

Data

Field

Data Frame

Control

Field

Control

Field

End of

Frame

CRC

Field

ACK

Field

Interframe

Space

11-bit base identifier

IDT28..18

18-bit identifier extension

ID17..0

18-bit identifier extension

ID17..0

Interframe

Space

4-bit DLC

DLC4..0

CRC

del.

ACK

del.

15-bit CRC

SOF

SRR

IDE r0

4-bit DLC

DLC4..0

RTR

r0r1

r1 ACK

7 bits

Intermission

3 bits

Bus Idle Bus Idle

(Indefinite)

Remote Frame

End of

Frame

CRC

Field

ACK

Field

Interframe

Space