Datasheet

ManualsBrandsMicrochip ManualsAVR MicrocontrollersAVR RISC Microcontroller 8bit 64KB TQFP

221

222

223

224

225

226

227

228

229

230

Table Of Contents

1. Description
- 1.1 Comparison Between AT90CAN32, AT90CAN64 and AT90CAN128
- 1.2 Part Description
- 1.3 Disclaimer
- 1.4 Block Diagram
- 1.5 Pin Configurations
- 1.6 Pin Descriptions
2. About Code Examples
3. AVR CPU Core
- 3.1 Introduction
- 3.2 Architectural Overview
- 3.3 ALU - Arithmetic Logic Unit
- 3.4 Status Register
- 3.5 General Purpose Register File
- 3.6 Stack Pointer
- 3.7 Instruction Execution Timing
- 3.8 Reset and Interrupt Handling
4. Memories
- 4.1 In-System Reprogrammable Flash Program Memory
- 4.2 SRAM Data Memory
- 4.3 EEPROM Data Memory
- 4.4 I/O Memory
- 4.5 External Memory Interface
- 4.6 General Purpose I/O Registers
5. System Clock
- 5.1 Clock Systems and their Distribution
- 5.2 Clock Sources
- 5.3 Default Clock Source
- 5.4 Crystal Oscillator
- 5.5 Low-frequency Crystal Oscillator
- 5.6 Calibrated Internal RC Oscillator
- 5.7 External Clock
- 5.8 Clock Output Buffer
- 5.9 Timer/Counter2 Oscillator
- 5.10 System Clock Prescaler
6. Power Management and Sleep Modes
- 6.1 Idle Mode
- 6.2 ADC Noise Reduction Mode
- 6.3 Power-down Mode
- 6.4 Power-save Mode
- 6.5 Standby Mode
- 6.6 Minimizing Power Consumption
7. System Control and Reset
- 7.1 Reset
- 7.2 Internal Voltage Reference
- 7.3 Watchdog Timer
- 7.4 Timed Sequences for Changing the Configuration of the Watchdog Timer
8. Interrupts
- 8.1 Interrupt Vectors in AT90CAN32/64/128
- 8.2 Moving Interrupts Between Application and Boot Space
9. I/O-Ports
- 9.1 Introduction
- 9.2 Ports as General Digital I/O
- 9.3 Alternate Port Functions
- 9.4 Register Description for I/O-Ports
10. External Interrupts
- 10.1 External Interrupt Register Description
11. Timer/Counter3/1/0 Prescalers
- 11.1 Overview
- 11.2 Timer/Counter0/1/3 Prescalers Register Description
12. 8-bit Timer/Counter0 with PWM
- 12.1 Features
- 12.2 Overview
- 12.3 Timer/Counter Clock Sources
- 12.4 Counter Unit
- 12.5 Output Compare Unit
- 12.6 Compare Match Output Unit
- 12.7 Modes of Operation
- 12.8 Timer/Counter Timing Diagrams
- 12.9 8-bit Timer/Counter Register Description
13. 16-bit Timer/Counter (Timer/Counter1 and Timer/Counter3)
- 13.1 Features
- 13.2 Overview
- 13.3 Accessing 16-bit Registers
- 13.4 Timer/Counter Clock Sources
- 13.5 Counter Unit
- 13.6 Input Capture Unit
- 13.7 Output Compare Units
- 13.8 Compare Match Output Unit
- 13.9 Modes of Operation
- 13.10 Timer/Counter Timing Diagrams
- 13.11 16-bit Timer/Counter Register Description
14. 8-bit Timer/Counter2 with PWM and Asynchronous Operation
- 14.1 Features
- 14.2 Overview
- 14.3 Timer/Counter Clock Sources
- 14.4 Counter Unit
- 14.5 Output Compare Unit
- 14.6 Compare Match Output Unit
- 14.7 Modes of Operation
- 14.8 Timer/Counter Timing Diagrams
- 14.9 8-bit Timer/Counter Register Description
- 14.10 Asynchronous operation of the Timer/Counter2
- 14.11 Timer/Counter2 Prescaler
15. Output Compare Modulator - OCM
- 15.1 Overview
- 15.2 Description
16. Serial Peripheral Interface - SPI
- 16.1 Features
- 16.2 SS Pin Functionality
- 16.3 Data Modes
17. USART (USART0 and USART1)
- 17.1 Features
- 17.2 Overview
- 17.3 Dual USART
- 17.4 Clock Generation
- 17.5 Serial Frame
- 17.6 USART Initialization
- 17.7 Data Transmission - USART Transmitter
- 17.8 Data Reception - USART Receiver
- 17.9 Asynchronous Data Reception
- 17.10 Multi-processor Communication Mode
- 17.11 USART Register Description
- 17.12 Examples of Baud Rate Setting
18. Two-wire Serial Interface
- 18.1 Features
- 18.2 Two-wire Serial Interface Bus Definition
- 18.3 Data Transfer and Frame Format
- 18.4 Multi-master Bus Systems, Arbitration and Synchronization
- 18.5 Overview of the TWI Module
- 18.6 TWI Register Description
- 18.7 Using the TWI
- 18.8 Transmission Modes
- 18.9 Multi-master Systems and Arbitration
19. Controller Area Network - CAN
- 19.1 Features
- 19.2 CAN Protocol
- 19.3 CAN Controller
- 19.4 CAN Channel
- 19.5 Message Objects
- 19.6 CAN Timer
- 19.7 Error Management
- 19.8 Interrupts
- 19.9 CAN Register Description
- 19.10 General CAN Registers
- 19.11 MOb Registers
- 19.12 Examples of CAN Baud Rate Setting
20. Analog Comparator
- 20.1 Overview
- 20.2 Analog Comparator Register Description
- 20.3 Analog Comparator Multiplexed Input
21. Analog to Digital Converter - ADC
- 21.1 Features
- 21.2 Operation
- 21.3 Starting a Conversion
- 21.4 Prescaling and Conversion Timing
- 21.5 Changing Channel or Reference Selection
- 21.6 ADC Noise Canceler
- 21.7 ADC Conversion Result
- 21.8 ADC Register Description
22. JTAG Interface and On-chip Debug System
- 22.1 Features
- 22.2 Overview
- 22.3 Test Access Port - TAP
- 22.4 TAP Controller
- 22.5 Using the Boundary-scan Chain
- 22.6 Using the On-chip Debug System
- 22.7 On-chip Debug Specific JTAG Instructions
- 22.8 On-chip Debug Related Register in I/O Memory
- 22.9 Using the JTAG Programming Capabilities
- 22.10 Bibliography
23. Boundary-scan IEEE 1149.1 (JTAG)
- 23.1 Features
- 23.2 System Overview
- 23.3 Data Registers
- 23.4 Boundary-scan Specific JTAG Instructions
- 23.5 Boundary-scan Related Register in I/O Memory
- 23.6 Boundary-scan Chain
- 23.7 AT90CAN32/64/128 Boundary-scan Order
- 23.8 Boundary-scan Description Language Files
24. Boot Loader Support - Read-While-Write Self-Programming
- 24.1 Features
- 24.2 Application and Boot Loader Flash Sections
- 24.3 Read-While-Write and No Read-While-Write Flash Sections
- 24.4 Boot Loader Lock Bits
- 24.5 Entering the Boot Loader Program
- 24.6 Addressing the Flash During Self-Programming
- 24.7 Self-Programming the Flash
25. Memory Programming
- 25.1 Program and Data Memory Lock Bits
- 25.2 Fuse Bits
- 25.3 Signature Bytes
- 25.4 Calibration Byte
- 25.5 Parallel Programming Overview
- 25.6 Parallel Programming
- 25.7 SPI Serial Programming Overview
- 25.8 SPI Serial Programming
- 25.9 JTAG Programming Overview
26. Electrical Characteristics (1)
- 26.1 Absolute Maximum Ratings*
- 26.2 DC Characteristics
- 26.3 External Clock Drive Characteristics
- 26.4 Maximum Speed vs. VCC
- 26.5 Two-wire Serial Interface Characteristics
- 26.6 SPI Timing Characteristics
- 26.7 CAN Physical Layer Characteristics
- 26.8 ADC Characteristics
- 26.9 External Data Memory Characteristics
- 26.10 Parallel Programming Characteristics
27. Decoupling Capacitors
28. AT90CAN32/64/128 Typical Characteristics
- 28.1 Active Supply Current
- 28.2 Idle Supply Current
- 28.3 Power-down Supply Current
- 28.4 Power-save Supply Current
- 28.5 Standby Supply Current
- 28.6 Pin Pull-up
- 28.7 Pin Driver Strength
- 28.8 Pin Thresholds and Hysteresis
- 28.9 BOD Thresholds and Analog Comparator Offset
- 28.10 Internal Oscillator Speed
- 28.11 Current Consumption of Peripheral Units
- 28.12 Current Consumption in Reset and Reset Pulse Width
29. Register Summary
30. Instruction Set Summary
31. Ordering Information
32. Packaging Information
- 32.1 TQFP64
- 32.2 QFN64
33. Errata
- 33.1 Errata Summary
- 33.2 Errata Description
34. Datasheet Revision History for AT90CAN32/64/128
- 34.1 Changes from 7679G - 03/08 to 7679H - 08/08
- 34.2 Changes from 7679F - 11/07 to 7679G - 03/08
- 34.3 Changes from 7679E - 07/07 to 7679F - 11/07
- 34.4 Changes from 7679D - 02/07 to 7679E - 07/07
- 34.5 Changes from 7679C - 01/07 to 7679D - 02/07
- 34.6 Changes from 7679B - 11/06 to 7679C - 01/07
- 34.7 Changes from 7679A - 10/06 to 7679B - 11/06
- 34.8 Document Creation

222

7679H–CAN–08/08

AT90CAN32/64/128

18.8.2 Master Receiver Mode

In the Master Receiver Mode, a number of data bytes are received from a slave transmitter (see

Figure 18-13). In order to enter a Master mode, a START condition must be transmitted. The for-

mat of the following address packet determines whether Master Transmitter or Master Receiver

mode is to be entered. If SLA+W is transmitted, MT mode is entered, if SLA+R is transmitted,

MR mode is entered. All the status codes mentioned in this section assume that the prescaler

bits are zero or are masked to zero.

Figure 18-13. Data Transfer in Master Receiver Mode

A START condition is sent by writing the following value to TWCR:

TWEN must be written to one to enable the Two-wire Serial Interface, TWSTA must be written to

one to transmit a START condition and TWINT must be set to clear the TWINT flag. The TWI will

then test the Two-wire Serial Bus and generate a START condition as soon as the bus becomes

free. After a START condition has been transmitted, the TWINT flag is set by hardware, and the

status code in TWSR will be 0x08 (See Table 18-3). In order to enter MR mode, SLA+R must be

transmitted. This is done by writing SLA+R to TWDR. Thereafter the TWINT bit should be

cleared (by writing it to one) to continue the transfer. This is accomplished by writing the follow-

ing value to TWCR:

When SLA+R have been transmitted and an acknowledgment bit has been received, TWINT is

set again and a number of status codes in TWSR are possible. Possible status codes in Master

mode are 0x38, 0x40, or 0x48. The appropriate action to be taken for each of these status codes

is detailed in Table 18-12. Received data can be read from the TWDR Register when the TWINT

flag is set high by hardware. This scheme is repeated until the last byte has been received. After

the last byte has been received, the MR should inform the ST by sending a NACK after the last

received data byte. The transfer is ended by generating a STOP condition or a repeated START

condition. A STOP condition is generated by writing the following value to TWCR:

TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN – TWIE

value 1

X10X10 X

TWCR TWINT

TWEA TWSTA TWSTO TWWC TWEN – TWIE

value 1

X00X10 X

TWCR TWINT

TWEA TWSTA TWSTO TWWC TWEN – TWIE

value 1

X01X10 X

Device 1

Device 2

Device 3

Device n

SDA

SCL

........

R1 R2

MASTER

SLAVE

TRANSMITTER

RECEIVER