Datasheet

 2002-2012 Microchip Technology Inc. DS21703L-page 3
24AA16/24LC16B
TABLE 1-2: AC CHARACTERISTICS
AC CHARACTERISTICS
Industrial (I): TA = -40°C to +85°C, VCC = +1.7V to +5.5V
Automotive (E): T
A = -40°C to +125°C, VCC = +1.7V to +5.5V
Param.
No.
Symbol Characteristic Min. Max. Units Conditions
1F
CLK Clock frequency —
—
400
100
kHz 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
2 THIGH Clock high time 600
4000
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
3T
LOW Clock low time 1300
4700
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
4TR SDA and SCL rise time
(Note 1)
—
—
300
1000
ns 2.5V  VCC  5.5V (Note 1)
1.7V  V
CC  2.5V (24AA16)
(Note 1)
5T
F SDA and SCL fall time — 300 ns (Note 1)
6T
HD:STA Start condition hold time 600
4000
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
7TSU:STA Start condition setup time 600
4700
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
8THD:DAT Data input hold time 0 — ns (Note 2)
9TSU:DAT Data input setup time 100
250
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
10 TSU:STO Stop condition setup time 600
4000
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
11 T
AA Output valid from clock
(Note 2)
—
—
900
3500
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
12 TBUF Bus free time: Time the bus
must be free before a new
transmission can start
1300
4700
—
—
ns 2.5V  VCC  5.5V
1.7V  V
CC  2.5V (24AA16)
13 T
OF Output fall time from VIH
minimum to V
IL maximum
20+0.1C
B
—
250
250
ns 2.5V  V
CC  5.5V
1.7V  V
CC 2.5V (24AA16)
14 TSP Input filter spike suppression
(SDA and SCL pins)
—50ns(Notes 1 and 3)
15 T
WC Write cycle time
(byte or page)
—5ms—
16 — Endurance 1M — cycles 25°C, (Note 4)
Note 1: Not 100% tested. C
B = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The combined T
SP and VHYS specifications are due to new Schmitt Trigger inputs which provide improved
noise spike suppression. This eliminates the need for a
TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site
at www.microchip.com.