User Manual
Table Of Contents
- Introduction
- Features
- Table of Contents
- 1. Ordering Information and Module Marking
- 2. Block Diagram
- 3. Pinout and Package Information
- 4. Electrical Characteristics
- 5. Power Management
- 6. Clocking
- 7. CPU and Memory Subsystem
- 8. WLAN Subsystem
- 9. Bluetooth Low Energy 4.0
- 10. External Interfaces
- 11. Application Reference Design
- 12. Module Outline Drawings
- 13. Design Consideration
- 14. Reflow Profile Information
- 15. Module Assembly Considerations
- 16. Regulatory Approval
- 17. Reference Documentation
- 18. Document Revision History
- The Microchip Web Site
- Customer Change Notification Service
- Customer Support
- Product Identification System
- Microchip Devices Code Protection Feature
- Legal Notice
- Trademarks
- Quality Management System Certified by DNV
- Worldwide Sales and Service
16.3 Europe
Note: Pending for an approval.
The ATWINC3400-MR210CA module is a Radio Equipment Directive (RED) assessed radio module that
is CE marked and has been manufactured and tested with the intention of being integrated into a final
product.
The ATWINC3400-MR210CA module has been tested to RED 2014/53/EU Essential Requirements for
Health and Safety (Article (3.1(a)), Electromagnetic Compatibility (EMC) (Article 3.1(b)), and Radio
(Article 3.2), which is summarized in the following European Compliance Testing table.
The ETSI provides guidance on modular devices in the “Guide to the application of harmonised standards
covering articles 3.1b and 3.2 of the RED 2014/53/EU (RED) to multi-radio and combined radio and non-
radio equipment” document available at http://www.etsi.org/deliver/etsi_eg/203300_203399/20
3367/01.01.01_60/eg_203367v010101p.pdf.
Note: To maintain conformance to the testing listed in the following European Compliance Testing table
the module shall be installed in accordance with the installation instructions in this data sheet and shall
not be modified. When integrating a radio module into a completed product, the integrator becomes the
manufacturer of the final product and is therefore responsible for demonstrating compliance of the final
product with the essential requirements against the RED.
16.3.1 Labeling and User Information Requirements
The label on the final product that contains the ATWINC3400-MR210CA module must follow CE marking
requirements.
Table 16-1. European Compliance Testing
Certification Standards Article Laborator
y
Report
Number
Date
Safety EN60950-1:2006/A11:2009/A1:2010/
A12:2011/A2:2013
[3.1.
(a)]
TUV
Rheinland,
Taiwan
10062655 001 30-
Oct-2017
Health EN300328 V2.1.1/EN62311:2008 50103733 001
50103734 001
30-
Oct-2017
EMC EN301489-1 V2.1.1
EN301489-1 V2.2.0
[3.1(b)] 10062417 001 30-
Oct-2017
EN301489-17 V3.1.1
EN301489-17 V3.2.0
Radio EN300328 V2.1.1 [3.2] 50103733 001
50103734 001
30-
Oct-2017
16.3.2 Conformity Assessment
From ETSI Guidance Note EG 203367, section 6.1, when non-radio products are combined with a radio
product:
If the manufacturer of the combined equipment installs the radio product in a host non-radio product in
equivalent assessment conditions (i.e. host equivalent to the one used for the assessment of the radio
product) and according to the installation instructions for the radio product, then no additional assessment
of the combined equipment against article 3.2 of the RED is required.
ATWINC3400-MR210CA
© 2017 Microchip Technology Inc.
Draft Datasheet Preliminary
DS00000000A-page 48