Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsIntegrated Circuits (ICs)16 Bit 2 M x 8

Microchip Technology Company

Data Sheet

www.microchip.com

16 Mbit (x8) Multi-Purpose Flash Plus

SST39VF1681 / SST39VF1682

Features

• Organized as 2M x8

• Single Voltage Read and Write Operations

– 2.7-3.6V

• Superior Reliability

– Endurance: 100,000 Cycles (Typical)

– Greater than 100 years Data Retention

• Low Power Consumption (typical values at 5 MHz)

– Active Current: 9 mA (typical)

– Standby Current: 3 µA (typical)

– Auto Low Power Mode: 3 µA (typical)

• Hardware Block-Protection/WP# Input Pin

– Top Block-Protection (top 64 KByte)

for SST39VF1682

– Bottom Block-Protection (bottom 64 KByte)

for SST39VF1681

• Sector-Erase Capability

– Uniform 4 KByte sectors

• Block-Erase Capability

– Uniform 64 KByte blocks

• Chip-Erase Capability

• Erase-Suspend/Erase-Resume Capabilities

• Hardware Reset Pin (RST#)

• Security-ID Feature

– SST: 128 bits; User: 128 bits

• Fast Read Access Time:

–70ns

• Latched Address and Data

• Fast Erase and Byte-Program:

– Sector-Erase Time: 18 ms (typical)

– Block-Erase Time: 18 ms (typical)

– Chip-Erase Time: 40 ms (typical)

– Byte-Program Time: 7 µs (typical)

• Automatic Write Timing

– Internal V

Generation

• End-of-Write Detection

– Toggle Bits

– Data# Polling

• CMOS I/O Compatibility

• JEDEC Standard

– Flash EEPROM Pinouts and Command sets

• Packages Available

– 48-ball TFBGA (6mm x 8mm)

– 48-lead TSOP (12mm x 20mm)

• All devices are RoHS compliant

The SST39VF1681 / SST39VF1682 are 2M x8 CMOS Multi-Purpose Flash Plus

(MPF+) manufactured with SST proprietary, high performance CMOS Super-

Flash® technology. The split-gate cell design and thick-oxide tunneling injector

attain better reliability and manufacturability compared with alternate approaches.

The SST39VF1681 / SST39VF1682 write (Program or Erase) with a 2.7-3.6V

power supply. These devices conforms to JEDEC standard pinouts for x8 memo-

ries.

Summary of content (34 pages)

PAGE 1
6 Mbit (x8) Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet The SST39VF1681 / SST39VF1682 are 2M x8 CMOS Multi-Purpose Flash Plus (MPF+) manufactured with SST proprietary, high performance CMOS SuperFlash® technology. The split-gate cell design and thick-oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches. The SST39VF1681 / SST39VF1682 write (Program or Erase) with a 2.7-3.6V power supply.
PAGE 2
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Product Description The SST39VF168x devices are 2M x8 CMOS Multi-Purpose Flash Plus (MPF+) manufactured with SST’s proprietary, high performance CMOS SuperFlash® technology. The split-gate cell design and thick-oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches. The SST39VF168x write (Program or Erase) with a 2.7-3.6V power supply.
PAGE 3
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Block Diagram SuperFlash Memory X-Decoder Memory Address Address Buffer Latches Y-Decoder CE# OE# WE# WP# RESET# I/O Buffers and Data Latches Control Logic DQ7 - DQ0 1243 B1.
PAGE 4
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet A16 A15 A14 A13 A12 A11 A10 A9 A20 NC WE# RST# NC WP# NC A19 A18 A8 A7 A6 A5 A4 A3 A2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 Standard Pinout Top View Die Up A17 NC VSS A0 DQ7 NC DQ6 NC DQ5 NC DQ4 VDD NC DQ3 NC DQ2 NC DQ1 NC DQ0 OE# VSS CE# A1 1243 48-tsop P2.
PAGE 5
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Device Operation Commands are used to initiate the memory operation functions of the device. Commands are written to the device using standard microprocessor write sequences. A command is written by asserting WE# low while keeping CE# low. The address bus is latched on the falling edge of WE# or CE#, whichever occurs last. The data bus is latched on the rising edge of WE# or CE#, whichever occurs first.
PAGE 6
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet timing waveforms and Figure 24 for the flowchart. Any commands issued during the Sector- or BlockErase operation are ignored. When WP# is low, any attempt to Sector- (Block-) Erase the protected block will be ignored. During the command sequence, WP# should be statically held high or low.
PAGE 7
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet duce a ‘0’. Once the internal Erase operation is completed, DQ7 will produce a ‘1’. The Data# Polling is valid after the rising edge of fourth WE# (or CE#) pulse for Program operation. For Sector-, Block- or Chip-Erase, the Data# Polling is valid after the rising edge of sixth WE# (or CE#) pulse. See Figure 7 for Data# Polling timing diagram and Figure 21 for a flowchart.
PAGE 8
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Hardware Block Protection The SST39VF1682 supports top hardware block protection, which protects the top 64 KByte block of the device. The SST39VF1681 supports bottom hardware block protection, which protects the bottom 64 KByte block of the device. The Boot Block address ranges are described in Table 3. Program and Erase operations are prevented on the 64 KByte when WP# is low.
PAGE 9
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Product Identification The Product Identification mode identifies the devices as the SST39VF1681 and SST39VF1682, and manufacturer as SST. Users may use the software Product Identification operation to identify the part (i.e., using the device ID) when using multiple manufacturers in the same socket.
PAGE 10
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Operations Table 5: Operation Modes Selection Mode CE# OE# WE# DQ Address Read VIL VIL VIH DOUT AIN Program VIL VIH VIL DIN AIN VIL X1 Sector or block address, XXH for Chip-Erase Erase VIL Standby VIH X X High Z X X VIL X High Z/ DOUT X X X VIH High Z/ DOUT X VIL VIL VIH Write Inhibit VIH Product Identification Software Mode See Table 6 T5.0 25040 1.
PAGE 11
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet 4. With AMS-A5 = 0; Sec ID is read with A4-A0, SST ID is read with A4 = 0 (Address range = 00000H to 0000FH), User ID is read with A4 = 1 (Address range = 00010H to 0001FH). Lock Status is read with A7-A0 = 0000FFH. Unlocked: DQ3 = 1 / Locked: DQ3 = 0. 5. Valid Byte Addresses for Sec ID are from 000000H-00000FH and 000020H-00002FH. 6. The device does not remain in Software Product ID Mode if powered down.
PAGE 12
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Table 9: Device Geometry Information Address 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H Data 15H 00H 00H 00H 00H 02H FFH 01H 10H 00H 1FH 00H 00H 01H Data Device size = 2N Bytes (15H = 21; 221 = 2 MByte) Flash Device Interface description; 00H = x8-only asynchronous interface Maximum number of byte in multi-byte write = 2N (00H = not supported) Number of Erase Sector/Block sizes supported by
PAGE 13
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied.
PAGE 14
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Table 12:DC Operating Characteristics VDD = 2.7-3.
PAGE 15
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Table 15:Reliability Characteristics Symbol Parameter Minimum Specification Units Test Method NEND1,2 Endurance 10,000 Cycles JEDEC Standard A117 TDR1 Data Retention 100 Years JEDEC Standard A103 ILTH1 Latch Up 100 + IDD mA JEDEC Standard 78 T15.2 25040 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. 2.
PAGE 16
Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Table 17:Program/Erase Cycle Timing Parameters Symbol Parameter Min Max Units 10 µs TBP Byte-Program Time TAS Address Setup Time 0 ns TAH Address Hold Time 30 ns TCS WE# and CE# Setup Time 0 ns TCH WE# and CE# Hold Time 0 ns TOES OE# High Setup Time 0 ns TOEH OE# High Hold Time 10 ns TCP CE# Pulse Width 40 ns TWP WE# Pulse Width 40 ns TWPH1 TCPH1 WE# Pulse Width Hi
PAGE 17
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet TRC TAA ADDRESS AMS-0 TCE CE# TOE OE# TOHZ TOLZ VIH WE# DQ15-0 TCHZ TOH TCLZ HIGH-Z HIGH-Z DATA VALID DATA VALID 1243 F02.
PAGE 18
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet INTERNAL PROGRAM OPERATION STARTS TBP AAA TAH ADDRESS AMS-0 555 AAA ADDR TDH TCP CE# TAS TDS TCPH OE# TCH WE# TCS DQ7-0 AA 55 A0 DATA SW0 SW1 SW2 BYTE (ADDR/DATA) 1243 F04.2 Note: AMS = Most Significant Address AMS = A20 for SST39VF168x WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence. X can be VIL or VIH, but no other value.
PAGE 19
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet ADDRESS AMS-0 TCE CE# TOEH TOES TOE OE# WE# DQ6 and DQ2 TWO READ CYCLES WITH SAME OUTPUTS 1243 F06.1 Note: AMS = Most Significant Address AMS = A20 for SST39VF168x Figure 8: Toggle Bits Timing Diagram TSCE SIX-BYTE CODE FOR CHIP-ERASE ADDRESS AMS-0 AAA 555 AAA AAA 555 AAA CE# OE# TWP WE# DQ7-0 AA 55 80 AA 55 10 SW0 SW1 SW2 SW3 SW4 SW5 1243 F07.
PAGE 20
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet TBE SIX-BYTE CODE FOR BLOCK-ERASE ADDRESS AMS-0 AAA 555 AAA AAA BAX 555 CE# OE# TWP WE# DQ7-0 AA 55 80 AA 55 30 SW0 SW1 SW2 SW3 SW4 SW5 1243 F08.1 Note: This device also supports CE# controlled Chip-Erase operation. The WE# and CE# signals are interchangeable as long as minimum timings are meet. (See Table 17.
PAGE 21
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet TSE SIX-BYTE CODE FOR SECTOR-ERASE ADDRESS AMS-0 AAA 555 AAA AAA SAX 555 CE# OE# TWP WE# DQ7-0 AA 55 80 AA 55 50 SW0 SW1 SW2 SW3 SW4 SW5 1243 F9.1 Note: This device also supports CE# controlled Chip-Erase operation. The WE# and CE# signals are interchangeable as long as minimum timings are meet. (See Table 17.
PAGE 22
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet THREE-BYTE SEQUENCE FOR SOFTWARE ID ENTRY ADDRESS AMS-0 AAA 555 AAA 0000 0001 CE# OE# TIDA TWP WE# TWPH DQ7-0 TAA AA 55 90 SW0 SW1 SW2 BF Device ID 1243 F10.1 Note: Device ID - See Table 4 on page 9 AMS = Most Significant Address AMS = A20 for SST39VF168x WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence.
PAGE 23
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet THREE-BYTE SEQUENCE FOR SOFTWARE ID EXIT AND RESET ADDRESS AMS-0 AAA 555 DQ7-0 AA AAA 55 F0 TIDA CE# OE# TWP WE# TWHP SW0 SW1 1243 F12.2 SW2 Note: AMS = Most Significant Address AMS = A20 for SST39VF168x WP# must be held in proper logic state (VIL or VIH) 1 µs prior to and 1 µs after the command sequence. X can be VIL or VIH, but no other value.
PAGE 24
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet TRP RST# CE#/OE# TRHR 1243 F14.0 Figure 16:RST# Timing Diagram (When no internal operation is in progress) TRP RST# TRY CE#/OE# End-of-Write Detection (Toggle-Bit) 1243 F15.0 Figure 17:RST# Timing Diagram (During Program or Erase operation) ©2011 Silicon Storage Technology, Inc.
PAGE 25
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet VIHT INPUT VIT REFERENCE POINTS VOT OUTPUT VILT 1243 F16.0 AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic “0”. Measurement reference points for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10%  90%) are <5 ns.
PAGE 26
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Start Load data: AAH Address: AAAH Load data: 55H Address: 555H Load data: A0H Address: AAAH Load Word Address/Word Data Wait for end of Program (TBP, Data# Polling bit, or Toggle bit operation) Program Completed 1243 F18.0 X can be VIL or VIH, but no other value Figure 20:Byte-Program Algorithm ©2011 Silicon Storage Technology, Inc.
PAGE 27
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Internal Timer Toggle Bit Data# Polling Program/Erase Initiated Program/Erase Initiated Program/Erase Initiated Wait TBP, TSCE, TSE or TBE Read word Read DQ7 Read same word Program/Erase Completed No Is DQ7 = true data Yes No Does DQ6 match Program/Erase Completed Yes Program/Erase Completed 1243 F19.0 Figure 21:Wait Options ©2011 Silicon Storage Technology, Inc.
PAGE 28
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet CFI Query Entry Command Sequence Sec ID Query Entry Command Sequence Software Product ID Entry Command Sequence Load data: AAH Address: AAAH Load data: AAH Address: AAAH Load data: AAH Address: AAAH Load data: 55H Address: 555H Load data: 55H Address: 555H Load data: 55H Address: 555H Load data: 98H Address: AAAH Load data: 88H Address: AAAH Load data: 90H Address: 5555H Wait TIDA Wait TIDA
PAGE 29
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Software ID Exit/CFI Exit/Sec ID Exit Command Sequence Load data: AAH Address: AAAH Load data: F0H Address: XXH Load data: 55H Address: 555H Wait TIDA Load data: F0H Address: AAAH Return to normal operation Wait TIDA Return to normal operation X can be VIL or VIH, but no other value 1243 F21.0 Figure 23:Software ID/CFI Exit Command Flowcharts ©2011 Silicon Storage Technology, Inc.
PAGE 30
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Chip-Erase Command Sequence Sector-Erase Command Sequence Block-Erase Command Sequence Load data: AAH Address: AAAH Load data: AAH Address: AAAH Load data: AAH Address: AAAH Load data: 55H Address: 555H Load data: 55H Address: 555H Load data: 55H Address: 555H Load data: 80H Address: AAAH Load data: 80H Address: AAAH Load data: 80H Address: AAAH Load data: AAH Address: AAAH Load data: AAH Add
PAGE 31
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Product Ordering Information SST 39 VF XX XX 1681 XXXX - 70 XX - 4C XX - B3KE XXXX Environmental Attribute E1 = non-Pb Package Modifier K = 48 leads Package Type B3 = TFBGA (6mm x 8mm, 0.
PAGE 32
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Packaging Diagrams 1.05 0.95 Pin # 1 Identifier 0.50 BSC 0.27 0.17 12.20 11.80 0.15 0.05 18.50 18.30 DETAIL 1.20 max. 0.70 0.50 20.20 19.80 0°- 5° Note: 1. Complies with JEDEC publication 95 MO-142 DD dimensions, although some dimensions may be more stringent. 2. All linear dimensions are in millimeters (max/min). 1mm 3. Coplanarity: 0.1 mm 4. Maximum allowable mold flash is 0.
PAGE 33
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet TOP VIEW BOTTOM VIEW 5.60 8.00 0.10 0.45 0.05 (48X) 0.80 6 6 5 5 4.00 4 4 6.00 0.10 3 3 2 2 1 1 0.80 A B C D E F G H A1 CORNER SIDE VIEW H G F E D C B A A1 CORNER 1.10 0.10 0.12 SEATING PLANE 1mm 0.35 0.05 Note: 1. Complies with JEDEC Publication 95, MO-210, variant AB-1 , although some dimensions may be more stringent. 2. All linear dimensions are in millimeters. 3.
PAGE 34
16 Mbit Multi-Purpose Flash Plus SST39VF1681 / SST39VF1682 A Microchip Technology Company Data Sheet Table 18:Revision History Number 00 01 02 03 A Description • • • • • • • • • • • • Date Initial release Change product number from 166x to 168x Added B3K package and associated MPNs (See page 31) Removed 90 ns Commercial temperature for the EK and EKE packages 2004 Data Book Updated B3K package diagram Updated document status to “Data Sheet.” Removed all 90ns information.