User's Manual

LED and Beep Signals
Green LED Beeper
Discoverable Blinks two None
Mode* times every
two seconds
Connected* Blinks once None
every two
seconds
Sleeping Does not blink None
Good Scan Blinks once Beeps once
Bar Code Blinks three Beeps three
Memory Full times times
Uploading Blinks twice per None
second while
the data is
uploading
Upload Blinks once Three beeps
Complete that descend
in pitch
*Cordless Scanner only
Setting Up Your Scanner
1. Obtain software from the seller.
2. Install the software. For instructions, see the
Software User's Guide.
3. Install the batteries in the scanner. Follow
the steps outlined in "Installing and Replacing
Batteries."
4. For a cordless scanner install the Bluetooth
adapter in the host device. The host device is
the PC or PDA that will receive the bar codes
from the scanner. For installation instructions,
see the documentation provided with the
adapter.
5. Configure the software to connect to the
scanner.
Note for Cordless Scanner:
Place the scanner in discoverable mode by
pressing the button.
The default Bluetooth Passkey is 0000.
6. Verify that the scanner is working
correctly, see the Software User's Guide.
How to Scan
1. Aim Scanner - Hold the scanner at a slight
angle to the bar code you wish to scan. (Fig. 1)
2. Press & Hold the Button on top of the scanner
to make the red laser line appear. The laser line
should cover the entire bar code symbol.
3. Release the Button after the Beep and the
the green light blinks. This indicates that the
scanner has successfully scanned the bar code
symbol. Try the sample bar code now.
Sample Bar Code
Scanner Modes
The scanner runs in two modes: real-time and
store-and-forward.
Real-time is when the scanner is connected to a cable
or a Bluetooth host device. The scanner uploads the
bar codes as you scan them.
Batch mode is when the scanner is disconnected or
out of range. It stores the bar codes in memory.
When you plug in the scanner or move it back into
range, the scanner automatically connects to the host
device and uploads the stored bar codes.
Three beeps indicates the scanner's memory is full. If
this occurs, either connect the cable or move the
scanner back into range of the Bluetooth host device
and wake up the scanner by pushing the button.
When connected, the scanner automatically uploads
the saved bar codes and clears its memory.
Installing and Replacing Batteries
Use only AAA Alkaline batteries in your
Scanner. Please remove the batteries when
you are storing the scanner for more than
30 days.
1. Turn the scanner over so that the back
faces up.
2. Remove the battery cover by pressing
the button at the top of the cover, and
moving the cover down.
3. If there are batteries in the scanner, remove
them.
4. Insert the new batteries so that the positive end
(+) is up on the outside batteries, and down on
the middle battery.
5. Replace the battery cover by inserting the tabs at
the top of the cover into the slots in the back of
the scanner. Slide the cover up.
Battery Life:
Scanner - 100,000+ continuous scans or 24,000+
scans over 12 months at 100 scans/day
Cordless - 76,000+ continuous scans or 16,000+
scans over 8 months at 100 scans/day
Operator's Guide
Laser Bar Code Scanner
The Scanner is a breakthrough in affordable laser
scanning. The scanner has the scanning
performance of more expensive laser scanners, the
convenience of hand-held portability, and the
advantage of optional Bluetooth
®
wireless
technology. In store-and-forward mode you can
capture approximately 500 (optional 4000) UPC bar
code symbols, and then automatically upload them
when you connect the scanner or move back into
range. The Cordless Scanner has a 10 to 15 meter
real-time operating range, and an unlimited
store-and-forward range with automatic
reconnection.
Limited Warranty
Manufacturer warrants that the scanner product will be free of
defects in material and workmanship for one (1) year from the date
of shipment. Manufacturer will, at its option, either repair, replace or
refund the purchase price paid by buyer for the defective products.
Such repair, replacement or refund shall be buyer's sole remedy in
the event of Manufacturer's breach of this limited warranty. Repaired
or replaced parts or product may include new, reconditioned or
re-manufactured parts and equipment at Manufacturer's option. All
costs associated with shipment to Manufacturer for warranty service,
including but not limited to freight, duties, insurance and customs
fees are buyer's responsibility. Manufacturer will pay the freight
costs (duties, insurance, customs and any other fees are buyer's
responsibility) associated with the return shipment to buyer. The
method of shipment will be at Manufacturer's discretion. Repair or
replacement of any parts or equipment does not extend the period of
warranty provided for herein. THIS LIMITED WARRANTY IS
MANUFACTURER'S ONLY WARRANTY. MANUFACTURER DOES NOT
GIVE WARRANTIES OF MERCHANTABILITY OR WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE. To take advantage of this
warranty, buyer should contact the seller not the Manufacturer.
The warranty set forth herein does not cover and Manufacturer will have
no obligations hereunder if any non-conformance is caused in whole or
in part by; accident, transportation, neglect, misuse, alteration,
modification, or enhancement of the products or incorporation,
interfacing, attachment of any feature, program, or device to the
Products by a person or entity other than Manufacturer, failure to
provide a suitable installation environment, use of the products for other
than the specific purpose for which the products are designed or any
use of the product not in accordance with the Operator's Guide or other
misuse or abuse of the product.
Legal Notice
The Bluetooth word, mark, and logo are owned by the Bluetooth SIG, Inc. and any
use of such marks by Manufacturer is under license.
This product is covered by one or more pending or issued patents.
DOCUMENT NUMBER: DA0116777-001 Rev. A
scan window
LED
indicator
scan button
battery door
with optional Bluetooth radio
serial port
Scanner
Cordless Scanner
Fig. 1
Fig. 2