Datasheet
2011 Microchip Technology Inc. DS39960D-page 489
PIC18F87K22 FAMILY
Supply Current (IDD)
(2,3)
All devices 5.3 10 µA -40°C
V
DD = 1.8V
(4)
Regulator Disabled
F
OSC = 31 kHz
(
RC_RUN mode,
LF-INTOSC)
5.5 10 µA +25°C
5.5 10 µA +85°C
12 24 µA +125ºC
All devices 10 15 µA -40°C
V
DD = 3.3V
(4)
Regulator Disabled
10 16 µA +25°C
11 17 µA +85°C
15 35 µA +125ºC
All devices 70 180 µA -40°C
V
DD = 5V
(5)
Regulator Enabled
80 185 µA +25°C
90 190 µA +85°C
200 500 µA +125ºC
All devices 410 850 µA -40°C
V
DD = 1.8V
(4)
Regulator Disabled
F
OSC = 1 MHz
(
RC_RUN mode,
HF-INTOSC)
410 800 µA +25°C
410 830 µA +85°C
700 1500 µA +125ºC
All devices 680 990 µA -40°C
V
DD = 3.3V
(4)
Regulator Disabled
680 960 µA +25°C
670 950 µA +85°C
800 1700 µA +125ºC
All devices 760 1400 µA -40°C
V
DD = 5V
(5)
Regulator Enabled
780 1400 µA +25°C
800 1500 µA +85°C
1200 2400 µA +125ºC
All devices 760 1300 µA -40°C
V
DD = 1.8V
(4)
Regulator Disabled
F
OSC = 4 MHz
(
RC_RUN mode,
HF-INTOSC)
760 1400 µA +25°C
770 1500 µA +85°C
800 1700 µA +125ºC
All devices 1.4 2.5 mA -40°C
V
DD = 3.3V
(4)
Regulator Disabled
1.4 2.5 mA +25°C
1.4 2.5 mA +85°C
1.5 3.0 mA +125ºC
All devices 1.5 2.7 mA -40°C
V
DD = 5V
(5)
Regulator Enabled
1.5 2.7 mA +25°C
1.5 2.7 mA +85°C
1.6 3.3 mA +125ºC
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial/Extended) (Continued)
PIC18F87K22 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C
TA +125°C for extended
Param
No.
Device Typ Max Units Conditions
Note 1:
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to V
DD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all I
DD measurements in Active Operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
5: Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
6: 48 MHz, maximum frequency at +125ºC.