Datasheet
2007-2012 Microchip Technology Inc. DS39778E-page 407
PIC18F87J11 FAMILY
Supply Current (IDD) Cont.
(2,3)
All devices 0.17 0.35 mA -40°C
V
DD = 2.0V,
V
DDCORE = 2.0V
(4)
FOSC = 1 MHZ
(PRI_RUN mode,
EC oscillator)
0.18 0.35 mA +25°C
0.20 0.42 mA +85°C
All devices 0.29 0.52 mA -40°C
V
DD = 2.5V,
V
DDCORE = 2.5V
(4)
0.31 0.52 mA +25°C
0.34 0.61 mA +85°C
All devices 0.59 1.1 mA -40°C
0.44 0.85 mA +25°C V
DD = 3.3V
(5)
0.42 0.85 mA +85°C
All devices 0.70 1.25 mA -40°C
V
DD = 2.0V,
V
DDCORE = 2.0V
(4)
FOSC = 4 MHz
(PRI_RUN mode,
EC oscillator)
0.75 1.25 mA +25°C
0.79 1.36 mA +85°C
All devices 1.10 1.7 mA -40°C
V
DD = 2.5V,
V
DDCORE = 2.5V
(4)
1.10 1.7 mA +25°C
1.12 1.82 mA +85°C
All devices 1.55 1.95 mA -40°C
1.47 1.89 mA +25°C V
DD = 3.3V
(5)
1.54 1.92 mA +85°C
All devices 9.9 14.8 mA -40°C
V
DD = 2.5V,
V
DDCORE = 2.5V
(4)
FOSC = 48 MHZ
(PRI_RUN mode,
EC oscillator)
9.5 14.8 mA +25°C
10.1 15.2 mA +85°C
All devices 13.3 23.2 mA -40°C
12.2 22.7 mA +25°C V
DD = 3.3V
(5)
12.1 22.7 mA +85°C
28.2 DC Characteristics: Power-Down and Supply Current
PIC18F87J11 Family (Industrial) (Continued)
PIC18F87J11 Family
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
Param
No.
Device Typ Max Units Conditions
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to V
DD or VSS, and all features that add delta
current are disabled (such as WDT, Timer1 oscillator, BOR, etc.).
2: The supply current is mainly a function of the operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an
impact on the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT is enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator is disabled (ENVREG = 0, tied to V
SS).
5: Voltage regulator is enabled (ENVREG = 1, tied to V
DD, REGSLP = 1).