Datasheet
2003-2013 Microchip Technology Inc. DS30491D-page 37
PIC18F6585/8585/6680/8680
FSR1H
PIC18F6X8X PIC18F8X8X
---- xxxx ---- uuuu ---- uuuu
FSR1L PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
BSR PIC18F6X8X PIC18F8X8X ---- 0000 ---- 0000 ---- uuuu
INDF2 PIC18F6X8X PIC18F8X8X N/A N/A N/A
POSTINC2 PIC18F6X8X PIC18F8X8X N/A N/A N/A
POSTDEC2 PIC18F6X8X PIC18F8X8X N/A N/A N/A
PREINC2 PIC18F6X8X PIC18F8X8X N/A N/A N/A
PLUSW2 PIC18F6X8X PIC18F8X8X N/A N/A N/A
FSR2H PIC18F6X8X PIC18F8X8X ---- xxxx ---- uuuu ---- uuuu
FSR2L PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
STATUS PIC18F6X8X PIC18F8X8X ---x xxxx ---u uuuu ---u uuuu
TMR0H PIC18F6X8X PIC18F8X8X 0000 0000 uuuu uuuu uuuu uuuu
TMR0L PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
T0CON PIC18F6X8X PIC18F8X8X 1111 1111 1111 1111 uuuu uuuu
OSCCON PIC18F6X8X PIC18F8X8X ---- 0000 ---- 0000 ---- uuuu
LVDCON PIC18F6X8X PIC18F8X8X --00 0101 --00 0101 --uu uuuu
WDTCON PIC18F6X8X PIC18F8X8X ---- ---0 ---- ---0 ---- ---u
RCON
(4)
PIC18F6X8X PIC18F8X8X 0--q 11qq 0--q qquu u--u qquu
TMR1H PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
TMR1L PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
T1CON PIC18F6X8X PIC18F8X8X 0-00 0000 u-uu uuuu u-uu uuuu
TMR2 PIC18F6X8X PIC18F8X8X 0000 0000 0000 0000 uuuu uuuu
PR2 PIC18F6X8X PIC18F8X8X 1111 1111 1111 1111 1111 1111
T2CON PIC18F6X8X PIC18F8X8X -000 0000 -000 0000 -uuu uuuu
SSPBUF PIC18F6X8X PIC18F8X8X xxxx xxxx uuuu uuuu uuuu uuuu
SSPADD PIC18F6X8X PIC18F8X8X 0000 0000 0000 0000 uuuu uuuu
SSPSTAT PIC18F6X8X PIC18F8X8X 0000 0000 0000 0000 uuuu uuuu
SSPCON1 PIC18F6X8X PIC18F8X8X 0000 0000 0000 0000 uuuu uuuu
SSPCON2 PIC18F6X8X PIC18F8X8X 0000 0000 0000 0000 uuuu uuuu
TABLE 3-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR
Resets
WDT Reset
RESET Instruction
Stack Resets
Wake-up via WDT
or Interrupt
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the
interrupt vector (0008h or 0018h).
3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
4: See Table 3-2 for Reset value for specific condition.
5: Bit 6 of PORTA, LATA, and TRISA are enabled in ECIO and RCIO Oscillator modes only. In all other
oscillator modes, they are disabled and read ‘0’.
6: Bit 6 of PORTA, LATA and TRISA are not available on all devices. When unimplemented, they read ‘0’.
7: This register reads all ‘0’s until ECAN is set up in Mode 1 or Mode 2.
18F8680.book Page 37 Tuesday, January 29, 2013 1:32 PM