Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller TQFP 80 (12x12) 8-Bit 40 MHz I/O number 67

407

408

409

410

411

412

413

414

415

416

Table Of Contents

Low-Power Features:
LCD Driver Module Features:
Special Microcontroller Features:
Flexible Oscillator Structure:
Peripheral Highlights:
Pin Diagrams
Pin Diagrams (Continued)
Table of Contents
Most Current Data Sheet
Errata
Customer Notification System
1.0 Device Overview
- 1.1 Core Features
- 1.2 LCD Driver
- 1.3 Other Special Features
- 1.4 Details on Individual Family Members
2.0 Guidelines for Getting Started with PIC18FJ Microcontrollers
- 2.1 Basic Connection Requirements
  - FIGURE 2-1: Recommended Minimum connections
- 2.2 Power Supply Pins
  - 2.2.1 Decoupling Capacitors
  - 2.2.2 Tank Capacitors
- 2.3 Master Clear (MCLR) Pin
  - FIGURE 2-2: Example of MCLR Pin Connections
- 2.4 Voltage Regulator Pins (ENVREG and Vcap/Vddcore)
  - FIGURE 2-3: Frequency vs. ESR Performance for Suggested Vcap
- 2.5 ICSP Pins
- 2.6 External Oscillator Pins
- 2.7 Unused I/Os
  - FIGURE 2-4: Suggested Placement of the Oscillator Circuit
3.0 Oscillator Configurations
- 3.1 Oscillator Types
  - FIGURE 3-1: PIC18F85J90 family Clock Diagram
- 3.2 Control Registers
  - Register 3-1: OSCCON: Oscillator Control Register
  - Register 3-2: OSCTUNE: Oscillator Tuning Register
- 3.3 Clock Sources and Oscillator Switching
  - 3.3.1 Clock Source Selection
  - 3.3.2 Oscillator Transitions
- 3.4 External Oscillator Modes
- 3.5 Internal Oscillator Block
- 3.6 Effects of Power-Managed Modes on the Various Clock Sources
- 3.7 Power-up Delays
  - TABLE 3-3: OSC1 and OSC2 Pin States in Sleep Mode
4.0 Power-Managed Modes
- 4.1 Selecting Power-Managed Modes
- 4.2 Run Modes
- 4.3 Sleep Mode
- 4.4 Idle Modes
- 4.5 Exiting Idle and Sleep Modes
5.0 Reset
- 5.1 RCON Register
  - FIGURE 5-1: Simplified Block Diagram of On-Chip Reset Circuit
  - Register 5-1: RCON: Reset Control Register
- 5.2 Master Clear (MCLR)
- 5.3 Power-on Reset (POR)
- 5.4 Brown-out Reset (BOR)
  - FIGURE 5-2: External Power-on Reset Circuit (for Slow Vdd Power-up)
  - 5.4.1 Detecting BOR
- 5.5 Configuration Mismatch (CM)
- 5.6 Power-up Timer (PWRT)
  - 5.6.1 Time-out Sequence
- 5.7 Reset State of Registers
  - TABLE 5-1: Status Bits, Their Significance and the Initialization Condition for RCON Register
  - TABLE 5-2: Initialization Conditions for All Registers
6.0 Memory Organization
- 6.1 Program Memory Organization
- 6.2 PIC18 Instruction Cycle
- 6.3 Data Memory Organization
- 6.4 Data Addressing Modes
- 6.5 Program Memory and the Extended Instruction Set
- 6.6 Data Memory and the Extended Instruction Set
7.0 Flash Program Memory
- 7.1 Table Reads and Table Writes
  - FIGURE 7-1: Table Read Operation
  - FIGURE 7-2: Table Write Operation
- 7.2 Control Registers
- 7.3 Reading the Flash Program Memory
  - FIGURE 7-4: Reads from Flash Program Memory
  - EXAMPLE 7-1: Reading a Flash Program Memory Word
- 7.4 Erasing Flash Program Memory
  - 7.4.1 Flash Program Memory Erase Sequence
    - EXAMPLE 7-2: Erasing a Flash Program Memory Block
- 7.5 Writing to Flash Program Memory
- 7.6 Flash Program Operation During Code Protection
  - TABLE 7-2: Registers Associated with Program Flash Memory
8.0 8 X 8 Hardware Multiplier
- 8.1 Introduction
- 8.2 Operation
9.0 Interrupts
- FIGURE 9-1: PIC18F85J90 family Interrupt Logic
- 9.1 INTCON Registers
- 9.2 PIR Registers
- 9.3 PIE Registers
- 9.4 IPR Registers
- 9.5 RCON Register
  - Register 9-13: RCON: Reset Control Register
- 9.6 INTx Pin Interrupts
- 9.7 TMR0 Interrupt
- 9.8 PORTB Interrupt-on-Change
- 9.9 Context Saving During Interrupts
  - EXAMPLE 9-1: Saving STATUS, WREG and BSR Registers in RAM
10.0 I/O Ports
- FIGURE 10-1: Generic I/O Port Operation
- 10.1 I/O Port Pin Capabilities
- 10.2 PORTA, TRISA and LATA Registers
- 10.3 PORTB, TRISB and LATB Registers
- 10.4 PORTC, TRISC and LATC Registers
- 10.5 PORTD, TRISD and LATD Registers
- 10.6 PORTE, TRISE and LATE Registers
- 10.7 PORTF, LATF and TRISF Registers
- 10.8 PORTG, TRISG and LATG Registers
- 10.9 PORTH, LATH and TRISH Registers
- 10.10 PORTJ, TRISJ and LATJ Registers
11.0 Timer0 Module
- Register 11-1: T0CON: Timer0 Control Register
- 11.1 Timer0 Operation
- 11.2 Timer0 Reads and Writes in 16-Bit Mode
  - FIGURE 11-1: Timer0 Block Diagram (8-Bit Mode)
  - FIGURE 11-2: Timer0 Block Diagram (16-Bit Mode)
- 11.3 Prescaler
  - 11.3.1 Switching Prescaler Assignment
- 11.4 Timer0 Interrupt
  - TABLE 11-1: Registers Associated with Timer0
12.0 Timer1 Module
- Register 12-1: T1CON: Timer1 Control Register
- 12.1 Timer1 Operation
  - FIGURE 12-1: Timer1 Block Diagram (8-Bit Mode)
  - FIGURE 12-2: Timer1 Block Diagram (16-Bit Read/Write Mode)
- 12.2 Timer1 16-Bit Read/Write Mode
- 12.3 Timer1 Oscillator
- 12.4 Timer1 Interrupt
- 12.5 Resetting Timer1 Using the CCP Special Event Trigger
- 12.6 Using Timer1 as a Real-Time Clock
  - EXAMPLE 12-1: Implementing a Real-Time Clock Using a Timer1 Interrupt Service
  - TABLE 12-2: Registers Associated with Timer1 as a Timer/Counter
13.0 Timer2 Module
- 13.1 Timer2 Operation
  - Register 13-1: T2CON: Timer2 Control Register
- 13.2 Timer2 Interrupt
- 13.3 Timer2 Output
  - FIGURE 13-1: Timer2 Block Diagram
  - TABLE 13-1: Registers Associated with Timer2 as a Timer/Counter
14.0 Timer3 Module
- Register 14-1: T3CON: Timer3 Control Register
- 14.1 Timer3 Operation
  - FIGURE 14-1: Timer3 Block Diagram (8-Bit Mode)
  - FIGURE 14-2: Timer3 Block Diagram (16-Bit Read/Write Mode)
- 14.2 Timer3 16-Bit Read/Write Mode
- 14.3 Using the Timer1 Oscillator as the Timer3 Clock Source
- 14.4 Timer3 Interrupt
- 14.5 Resetting Timer3 Using the CCP Special Event Trigger
  - TABLE 14-1: Registers Associated with Timer3 as a Timer/Counter
15.0 Capture/Compare/PWM (CCP) Modules
- Register 15-1: CCPxCON: CCPx Control Register (CCP1, CCP2 Modules)
- 15.1 CCP Module Configuration
- 15.2 Capture Mode
- 15.3 Compare Mode
- 15.4 PWM Mode
16.0 Liquid Crystal Display (LCD) Driver Module
- FIGURE 16-1: LCD Driver Module Block Diagram
- 16.1 LCD Registers
  - 16.1.1 LCD Control Registers
  - 16.1.2 LCD Data Registers
    - Register 16-4: LCDDATAx: LCD Data Registers
    - TABLE 16-2: LCDDATA Registers and Bits for Segment and COM Combinations
- 16.2 LCD Clock Source
  - 16.2.1 LCD Voltage Regulator Clock Source
  - 16.2.2 Clock sOURCE cONSIDERATIONS
    - FIGURE 16-2: LCD Clock Generation
- 16.3 LCD Bias Generation
- 16.4 LCD Multiplex Types
  - TABLE 16-3: PORTE<6:4> Function
- 16.5 Segment Enables
- 16.6 Pixel Control
- 16.7 LCD Frame Frequency
  - TABLE 16-4: Frame Frequency Formulas
  - TABLE 16-5: Approximate Frame Frequency (in Hz) for LP Prescaler Settings
- 16.8 LCD Waveform Generation
- 16.9 LCD Interrupts
  - FIGURE 16-17: Example Waveforms and Interrupt Timing in Quarter Duty Cycle Drive
- 16.10 Operation During Sleep
  - 16.10.1 Using the LCD Regulator During Sleep
    - FIGURE 16-18: Sleep Entry/Exit When SLPEN = 1 or CS<1:0> = 00
- 16.11 Configuring the LCD Module
  - TABLE 16-6: Registers Associated with LCD Operation
17.0 Master Synchronous Serial Port (MSSP) Module
- 17.1 Master SSP (MSSP) Module Overview
- 17.2 Control Registers
- 17.3 SPI Mode
- 17.4 I2C Mode
18.0 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART)
- 18.1 Control Registers
- 18.2 EUSART Baud Rate Generator (BRG)
- 18.3 EUSART Asynchronous Mode
- 18.4 EUSART Synchronous Master Mode
  - 18.4.1 EUSART Synchronous Master Transmission
  - 18.4.2 EUSART Synchronous Master Reception
    - FIGURE 18-13: Synchronous Reception (Master Mode, SREN)
    - TABLE 18-8: Registers Associated with Synchronous Master Reception
- 18.5 EUSART Synchronous Slave Mode
  - 18.5.1 EUSART Synchronous Slave Transmit
    - TABLE 18-9: Registers Associated with Synchronous Slave Transmission
  - 18.5.2 EUSART Synchronous Slave Reception
    - TABLE 18-10: Registers Associated with Synchronous Slave Reception
19.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (AUSART)
- 19.1 Control Registers
  - Register 19-1: TXSTA2: AUSART Transmit Status and Control Register
  - Register 19-2: RCSTA2: ausart Receive Status and Control Register
- 19.2 AUSART Baud Rate Generator (BRG)
  - 19.2.1 Operation in Power-Managed Modes
  - 19.2.2 Sampling
- 19.3 AUSART Asynchronous Mode
- 19.4 AUSART Synchronous Master Mode
  - 19.4.1 AUSART Synchronous Master Transmission
  - 19.4.2 AUSART Synchronous Master Reception
    - FIGURE 19-8: Synchronous Reception (Master Mode, SREN)
    - TABLE 19-7: Registers Associated with Synchronous Master Reception
- 19.5 AUSART Synchronous Slave Mode
  - 19.5.1 AUSART Synchronous Slave Transmit
    - TABLE 19-8: Registers Associated with Synchronous Slave Transmission
  - 19.5.2 AUSART Synchronous Slave Reception
    - TABLE 19-9: Registers Associated with Synchronous Slave Reception
20.0 10-bit Analog-to-Digital Converter (A/D) Module
- Register 20-1: ADCON0: A/D Control Register 0
- Register 20-2: ADCON1: A/D Control Register 1
- Register 20-3: ADCON2: A/D Control Register 2
- FIGURE 20-1: A/D Block Diagram(1,2)
- FIGURE 20-2: Analog Input Model
- 20.1 A/D Acquisition Requirements
- 20.2 Selecting and Configuring Automatic Acquisition Time
- 20.3 Selecting the A/D Conversion Clock
  - TABLE 20-1: Tad vs. Device Operating Frequencies
- 20.4 Configuring Analog Port Pins
- 20.5 A/D Conversions
- 20.6 Use of the CCP2 Trigger
  - FIGURE 20-3: A/D Conversion Tad Cycles (ACQT<2:0> = 000, Tacq = 0)
  - FIGURE 20-4: A/D Conversion Tad Cycles (ACQT<2:0> = 010, Tacq = 4 Tad)
- 20.7 A/D Converter Calibration
- 20.8 Operation in Power-Managed Modes
  - TABLE 20-2: Summary of A/D Registers
21.0 Comparator Module
- Register 21-1: CMCON: Comparator Module Control Register
- 21.1 Comparator Configuration
  - FIGURE 21-1: Comparator I/O Operating Modes
- 21.2 Comparator Operation
- 21.3 Comparator Reference
- 21.4 Comparator Response Time
- 21.5 Comparator Outputs
  - FIGURE 21-3: Comparator Output Block Diagram
- 21.6 Comparator Interrupts
- 21.7 Comparator Operation During Sleep
- 21.8 Effects of a Reset
- 21.9 Analog Input Connection Considerations
  - FIGURE 21-4: Comparator Analog Input Model
  - TABLE 21-1: Registers Associated with Comparator Module
22.0 Comparator Voltage Reference Module
- 22.1 Configuring the Comparator Voltage Reference
  - Register 22-1: CVRCON: Comparator Voltage Reference Control Register
  - FIGURE 22-1: Comparator Voltage Reference Block Diagram
- 22.2 Voltage Reference Accuracy/Error
- 22.3 Operation During Sleep
- 22.4 Effects of a Reset
- 22.5 Connection Considerations
  - FIGURE 22-2: Comparator Voltage Reference Output Buffer Example
  - TABLE 22-1: Registers Associated with Comparator Voltage Reference
23.0 Special Features of the CPU
- 23.1 Configuration Bits
  - 23.1.1 Considerations for Configuring the PIC18F85J90 family Devices
- 23.2 Watchdog Timer (WDT)
  - 23.2.1 Control Register
- 23.3 On-Chip Voltage Regulator
- 23.4 Two-Speed Start-up
  - FIGURE 23-3: Timing Transition for Two-Speed Start-up (INTRC to HSPLL)
  - 23.4.1 Special Considerations for Using Two-Speed Start-up
- 23.5 Fail-Safe Clock Monitor
- 23.6 Program Verification and Code Protection
  - 23.6.1 Configuration Register Protection
- 23.7 In-Circuit Serial Programming
- 23.8 In-Circuit Debugger
  - TABLE 23-4: Debugger Resources
24.0 Instruction Set Summary
- 24.1 Standard Instruction Set
- 24.2 Extended Instruction Set
25.0 Development Support
- 25.1 MPLAB Integrated Development Environment Software
- 25.2 MPLAB C Compilers for Various Device Families
- 25.3 HI-TECH C for Various Device Families
- 25.4 MPASM Assembler
- 25.5 MPLINK Object Linker/ MPLIB Object Librarian
- 25.6 MPLAB Assembler, Linker and Librarian for Various Device Families
- 25.7 MPLAB SIM Software Simulator
- 25.8 MPLAB REAL ICE In-Circuit Emulator System
- 25.9 MPLAB ICD 3 In-Circuit Debugger System
- 25.10 PICkit 3 In-Circuit Debugger/ Programmer and PICkit 3 Debug Express
- 25.11 PICkit 2 Development Programmer/Debugger and PICkit 2 Debug Express
- 25.12 MPLAB PM3 Device Programmer
- 25.13 Demonstration/Development Boards, Evaluation Kits, and Starter Kits
26.0 Electrical Characteristics
- Absolute Maximum Ratings(†)
  - FIGURE 26-1: PIC18F85J90 family Voltage-frequency Graph, Regulator Enabled (Industrial)(1)
  - FIGURE 26-2: PIC18F85J90 family Voltage-frequency Graph, Regulator Disabled (Industrial)(1,2)
- 26.1 DC Characteristics: Supply Voltage PIC18F85J90 Family (Industrial)
- 26.2 DC Characteristics: Power-Down and Supply Current PIC18F85J90 Family (Industrial)
- 26.3 DC Characteristics: PIC18F84J90 Family (Industrial)
- 26.4 AC (Timing) Characteristics
27.0 Packaging Information
- 27.1 Package Marking Information
- 27.2 Package Details
Appendix A: Revision History
- Revision A (July 2006)
- Revision B (March 2007)
- Revision C (January 2010)
Appendix B: Migration Between High-End Device Families
- TABLE B-1: Notable Differences Between PIC18F8490 and PIC18F85J90 Families
- TABLE B-2: Assignments of Moved LCD Segments
Index
The Microchip Web Site
Customer Change Notification Service
Customer Support
Reader Response
Product Identification System
Worldwide Sales and Service

PIC18F85J90 FAMILY

DS39770C-page 412  2010 Microchip Technology Inc.

Transition for Entry to SEC_RUN Mode .................... 45

Transition for Entry to Sleep Mode ............................47

Transition for Two-Speed Start-up

(INTRC to HSPLL) ........................................... 300

Transition for Wake From Idle to Run Mode .............. 48

Transition for Wake From Sleep (HSPLL) ................. 47

Transition From RC_RUN Mode to

PRI_RUN Mode ................................................. 46

Transition From SEC_RUN Mode to

PRI_RUN Mode (HSPLL) .................................. 45

Transition to RC_RUN Mode ..................................... 46

Type-A in 1/2 MUX, 1/2 Bias Drive ..........................176

Type-A in 1/2 MUX, 1/3 Bias Drive ..........................178

Type-A in 1/3 MUX, 1/2 Bias Drive ..........................180

Type-A in 1/3 MUX, 1/3 Bias Drive ..........................182

Type-A in 1/4 MUX, 1/3 Bias Drive ..........................184

Type-A/Type-B in Static Drive .................................. 175

Type-B in 1/2 MUX, 1/2 Bias Drive ..........................177

Type-B in 1/2 MUX, 1/3 Bias Drive ..........................179

Type-B in 1/3 MUX, 1/2 Bias Drive ..........................181

Type-B in 1/3 MUX, 1/3 Bias Drive ..........................183

Type-B in 1/4 MUX, 1/3 Bias Drive ..........................185

Timing Diagrams and Specifications

Capture/Compare/PWM Requirements

(CCP1, CCP2) .................................................381

CLKO and I/O Requirements ................................... 378

EUSART/AUSART Synchronous Receive

Requirements ................................................... 390

EUSART/AUSART Synchronous Transmission

Requirements ................................................... 390

Example SPI Mode Requirements

(Master Mode, CKE = 0) ................................. 382

Example SPI Mode Requirements

(Master Mode, CKE = 1) ................................. 383

Example SPI Mode Requirements

(Slave Mode, CKE = 0) .................................... 384

Example SPI Slave Mode

Requirements (CKE = 1) .................................. 385

External Clock Requirements .................................. 376

C Bus Data Requirements (Slave Mode) .............. 387

C Bus Start/Stop Bits Requirements

(Slave Mode) .................................................... 386

Internal RC Accuracy ............................................... 377

MSSP I

C Bus Data Requirements ......................... 389

MSSP I

C Bus Start/Stop Bits Requirements .......... 388

PLL Clock ................................................................ 377

Reset, Watchdog Timer, Oscillator Start-up

Timer, Power-up Timer and Brown-out

Reset Requirements ........................................ 379

Timer0 and Timer1 External Clock

Requirements .................................................. 380

Top-of-Stack Access .......................................................... 65

TSTFSZ ........................................................................... 345

Two-Speed Start-up ................................................. 291, 300

Two-Word Instructions

Example Cases .......................................................... 69

VDDCORE/VCAP Pin .......................................................... 299

Voltage Reference Specifications .................................... 373

Voltage Regulator (On-Chip) ........................................... 299

Brown-out Reset (BOR) ........................................... 300

Low-Voltage Detection (LVD) .................................. 299

Operation in Sleep Mode ......................................... 300

Power-up Requirements .......................................... 300

Watchdog Timer (WDT) ........................................... 291, 297

Associated Registers ............................................... 298

Control Register ....................................................... 297

During Oscillator Failure .......................................... 301

Programming Considerations .................................. 297

WCOL ...................................................... 223, 224, 225, 228

WCOL Status Flag ................................... 223, 224, 225, 228

WWW Address ................................................................ 413

WWW, On-Line Support ...................................................... 7

XORLW ............................................................................ 345

XORWF ........................................................................... 346