Datasheet

 2010 Microchip Technology Inc. DS39770C-page 369
PIC18F85J90 FAMILY
D022
(I
WDT)
Module Differential Currents (I
WDT, ILCD, IOSCB, IAD)
Watchdog Timer 1.6 4 µA -40°C
V
DD = 2.0V,
V
DDCORE = 2.0V
(4)
1.7 4 µA +25°C
1.6 4 µA +85°C
2.5 5 µA -40°C
V
DD = 2.5V,
V
DDCORE = 2.5V
(4)
2.5 5 µA +25°C
2.3 5 µA +85°C
3.8 6 µA -40°C
V
DD = 3.3V
(5)
2.6 6 µA +25°C
2.4 6 µA +85°C
D024
(I
LCD)
LCD Module 2
(6,7)
5 µA +25°C VDD = 2.0V Resistive Ladder
CPEN = 0;
CKSEL<1:0> = 00;
CS<1:0> = 10;
LP<3:0> = 0100
2.7
(6,7)
5 µA +25°C VDD = 2.5V
3.5
(6,7)
7 µA +25°C
V
DD = 3.0V
16
(7)
25 µA +25°C VDD = 2.0V Charge Pump
BIAS<2:0> = 111;
CPEN = 1;
CKSEL<1:0> = 11;
CS<1:0> = 10
17
(7)
25 µA +25°C VDD = 2.5V
24
(7)
40 µA +25°C
V
DD = 3.0V
D025
(I
OSCB)
Timer1 Oscillator 6.6 12.5 µA -40°C
V
DD = 2.0V,
V
DDCORE = 2.0V
(4)
32 kHz on Timer1
(3)
7.9 12.5 µA +25°C
11.5 18.5 µA +85°C
7.2 12.5 µA -40°C
V
DD = 2.5V,
V
DDCORE = 2.5V
(4)
32 kHz on Timer1
(3)
8.1 12.5 µA +25°C
11.9 18.5 µA +85°C
7 12.5 µA -40°C
V
DD = 3.3V
(5)
32 kHz on Timer1
(3)
9 12.5 µA +25°C
11 18.5 µA +85°C
D026
(I
AD)
A/D Converter 1 1.5 µA -40°C to +85°C V
DD = 2.0V,
V
DDCORE = 2.0V
(4)
A/D on, not converting1 1.5 µA -40°C to +85°C VDD = 2.5V,
V
DDCORE = 2.5V
(4)
1 1.5 µA -40°C to +85°C VDD = 3.3V
(5)
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F85J90 Family (Industrial) (Continued)
PIC18F85J90 Family
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
Param
No.
Device Typ Max Units Conditions
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to V
DD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator is disabled (ENVREG tied to V
SS).
5: Voltage regulator is enabled (ENVREG tied to V
DD).
6: Resistor ladder current is not included.
7: Connecting an actual display will increase the current consumption depending on the size of the LCD.