Datasheet

PIC18F2585/2680/4585/4680
DS39625C-page 256 Preliminary © 2007 Microchip Technology Inc.
19.7 Use of the CCP1 Trigger
An A/D conversion can be started by the “special event
trigger” of the ECCP1 module. This requires that the
ECCP1M3:ECCP1M0 bits (ECCP1CON<3:0>) be
programmed as ‘1011’ and that the A/D module is
enabled (ADON bit is set). When the trigger occurs, the
GO/DONE
bit will be set, starting the A/D acquisition
and conversion and the Timer1 (or Timer3) counter will
be reset to zero. Timer1 (or Timer3) is reset to automat-
ically repeat the A/D acquisition period with minimal
software overhead (moving ADRESH/ADRESL to the
desired location). The appropriate analog input
channel must be selected and the minimum acquisition
period is either timed by the user, or an appropriate
T
ACQ time selected before the “special event trigger”
sets the GO/DONE
bit (starts a conversion).
If the A/D module is not enabled (ADON is cleared), the
“special event trigger” will be ignored by the A/D
module, but will still reset the Timer1 (or Timer3)
counter.
TABLE 19-2: REGISTERS ASSOCIATED WITH A/D OPERATION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reset
Values
on page
INTCON GIE/GIEH PEIE/GIEL
TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 49
IPR1 PSPIP
(1)
ADIP RCIP TXIP SSPIP CCP1IP TMR2IP TMR1IP 52
PIR1
PSPIF
(1)
ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 52
PIE1 PSPIE
(1)
ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 52
IPR2 OSCFIP CMIP
(5)
— EEIP BCLIP HLVDIP TMR3IP ECCP1IP
(5)
51
PIR2
OSCFIF CMIF
(5)
— EEIF BCLIF HLVDIF TMR3IF ECCP1IF
(5)
51
PIE2 OSCFIE CMIE
(5)
— EEIE BCLIE HLVDIE TMR3IE ECCP1IE
(5)
52
ADRESH A/D Result Register High Byte 50
ADRESL A/D Result Register Low Byte 50
ADCON0
— — CHS3 CHS2 CHS1 CHS0 GO/DONE ADON 50
ADCON1 — — VCFG1 VCFG0 PCFG3 PCFG2 PCFG1 PCFG0 50
ADCON2 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 50
PORTA RA7
(2)
RA6
(2)
RA5 RA4 RA3 RA2 RA1 RA0 52
TRISA TRISA7
(2)
TRISA6
(2)
PORTA Data Direction Register 52
PORTB Read PORTB pins, Write LATB Latch 52
TRISB PORTB Data Direction Register 52
LATB PORTB Output Data Latch 52
PORTE
(4)
— — — —RE3
(3)
Read PORTE pins, Write LATE
(1)
52
TRISE
(4)
IBF OBF IBOV PSPMODE — PORTE Data Direction 52
LATE
(4)
— — — — — LATE2 LATE1 LATE0 52
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for A/D conversion.
Note 1: These bits are unimplemented on PIC18F2X8X devices; always maintain these bits clear.
2: These pins may be configured as port pins depending on the oscillator mode selected.
3: RE3 port bit is available only as an input pin when the MCLRE Configuration bit is ‘0’.
4: These registers are not implemented on PIC18F2X8X devices.
5: These bits are available on PIC18F4X8X and reserved on PIC18F2X8X devices.