Datasheet
PIC18F45J10 FAMILY
DS39682E-page 48 © 2009 Microchip Technology Inc.
INDF2 PIC18F2XJ10 PIC18F4XJ10 N/A N/A N/A
POSTINC2 PIC18F2XJ10 PIC18F4XJ10 N/A N/A N/A
POSTDEC2 PIC18F2XJ10 PIC18F4XJ10 N/A N/A N/A
PREINC2 PIC18F2XJ10 PIC18F4XJ10 N/A N/A N/A
PLUSW2 PIC18F2XJ10 PIC18F4XJ10 N/A N/A N/A
FSR2H PIC18F2XJ10 PIC18F4XJ10 ---- xxxx ---- uuuu ---- uuuu
FSR2L PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
STATUS PIC18F2XJ10 PIC18F4XJ10 ---x xxxx ---u uuuu ---u uuuu
TMR0H PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
TMR0L PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
T0CON PIC18F2XJ10 PIC18F4XJ10 1111 1111 1111 1111 uuuu uuuu
OSCCON PIC18F2XJ10 PIC18F4XJ10 0--- q-00 0--- q-00 u--- q-uu
WDTCON PIC18F2XJ10 PIC18F4XJ10 ---- ---0 ---- ---0 ---- ---u
RCON
(4)
PIC18F2XJ10 PIC18F4XJ10 0-11 11q0 0-qq qquu u-uu qquu
TMR1H PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
TMR1L PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
T1CON PIC18F2XJ10 PIC18F4XJ10 0000 0000 u0uu uuuu uuuu uuuu
TMR2 PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
PR2 PIC18F2XJ10 PIC18F4XJ10 1111 1111 1111 1111 1111 1111
T2CON PIC18F2XJ10 PIC18F4XJ10 -000 0000 -000 0000 -uuu uuuu
SSP1BUF PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
SSP1ADD PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
SSP1STAT PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
SSP1CON1 PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
SSP1CON2 PIC18F2XJ10 PIC18F4XJ10 0000 0000 0000 0000 uuuu uuuu
ADRESH PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
ADRESL PIC18F2XJ10 PIC18F4XJ10 xxxx xxxx uuuu uuuu uuuu uuuu
ADCON0 PIC18F2XJ10 PIC18F4XJ10 0-00 0000 0-00 0000 u-uu uuuu
ADCON1 PIC18F2XJ10 PIC18F4XJ10 --00 0qqq --00 0qqq --uu uqqq
ADCON2 PIC18F2XJ10 PIC18F4XJ10 0-00 0000 0-00 0000 u-uu uuuu
TABLE 5-2: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Register Applicable Devices
Power-on Reset,
Brown-out Reset
MCLR
Resets,
WDT Reset,
RESET Instruction,
Stack Resets,
CM Resets
Wake-up via WDT
or Interrupt
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt
vector (0008h or 0018h).
3: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
4: See Table 5-1 for Reset value for specific condition.