Datasheet

PIC18F2585/2680/4585/4680
DS39625C-page 424 Preliminary © 2007 Microchip Technology Inc.
Supply Current (I
DD)
(2,3)
PIC18LFX585/X680 22.00 44.00 μA -40°C
V
DD = 2.0V
F
OSC = 32 kHz
(4)
(SEC_RUN mode,
Timer1 as clock)
20.00 44.00 μA +25°C
19.00 44.00 μA +85°C
PIC18LFX585/X680 56.00 71.00 μA -40°C
VDD = 3.0V45.00 71.00 μA +25°C
41.00 71.00 μA +85°C
All devices 138.00 162.00 μA -40°C
V
DD = 5.0V106.00 162.00 μA +25°C
95.00 162.00 μA +85°C
PIC18LFX585/X680 6.20 24.00 μA -40°C
V
DD = 2.0V
F
OSC = 32 kHz
(4)
(SEC_IDLE mode,
Timer1 as clock)
6.60 24.00 μA +25°C
7.70 24.00 μA +85°C
PIC18LFX585/X680 9.30 33.00 μA -40°C
VDD = 3.0V9.40 33.00 μA +25°C
11.00 33.00 μA +85°C
All devices 17.00 50.00 μA -40°C
V
DD = 5.0V17.00 50.00 μA +25°C
20.00 50.00 μA +85°C
27.2 DC Characteristics: Power-Down and Supply Current
PIC18F2585/2680/4585/4680 (Industrial)
PIC18LF2585/2680/4585/4680 (Industrial) (Continued)
PIC18LF2585/2680/4585/4680
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
PIC18F2585/2680/4585/4680
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD or VSS and all features that add delta current
disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption. The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be estimated
by the formula Ir = V
DD/2REXT (mA) with REXT in kΩ.
4: Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.