Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller QFN 44 (8x8) 8-Bit 48 MHz I/O number 35

PIC18F2455/2550/4455/4550

CCPR1H 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

CCPR1L 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

CCP1CON 2455 2550

4455 4550 --00 0000 --00 0000 --uu uuuu

2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

CCPR2H 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

CCPR2L 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

CCP2CON 2455 2550 4455 4550 --00 0000 --00 0000 --uu uuuu

BAUDCON 2455 2550 4455 4550 0100 0-00 0100 0-00 uuuu u-uu

ECCP1DEL 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

ECCP1AS 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

CVRCON 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

CMCON 2455 2550 4455 4550 0000 0111 0000 0111 uuuu uuuu

TMR3H 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

TMR3L 2455 2550 4455 4550 xxxx xxxx uuuu uuuu uuuu uuuu

T3CON 2455 2550 4455 4550 0000 0000 uuuu uuuu uuuu uuuu

SPBRGH 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

SPBRG 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

RCREG 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

TXREG 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

TXSTA 2455 2550 4455 4550 0000 0010 0000 0010 uuuu uuuu

RCSTA 2455 2550 4455 4550 0000 000x 0000 000x uuuu uuuu

EEADR 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

EEDATA 2455 2550 4455 4550 0000 0000 0000 0000 uuuu uuuu

EECON2 2455 2550 4455 4550 0000 0000 0000 0000 0000 0000

EECON1 2455 2550 4455 4550 xx-0 x000 uu-0 u000 uu-0 u000

TABLE 4-4: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)

Power-on Reset,

Brown-out Reset

MCLR

Resets,

WDT Reset,

RESET Instruction,

Stack Resets

Wake-up via WDT

or Interrupt

Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.

Shaded cells indicate conditions do not apply for the designated device.

Note 1: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are

updated with the current value of the PC. The STKPTR is modified to point to the next location in the

hardware stack.

2: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).

3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the interrupt

vector (0008h or 0018h).

4: See Table 4-3 for Reset value for specific condition.

5: PORTA<6>, LATA<6> and TRISA<6> are enabled depending on the oscillator mode selected. When not

enabled as PORTA pins, they are disabled and read ‘0’.