Datasheet

PIC18FXX2
DS39564C-page 46 © 2006 Microchip Technology Inc.
TABLE 4-2: REGISTER FILE SUMMARY
File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Value on
POR, BOR
Details
on page:
TOSU
— — — Top-of-Stack upper Byte (TOS<20:16>) ---0 0000 37
TOSH Top-of-Stack High Byte (TOS<15:8>) 0000 0000 37
TOSL Top-of-Stack Low Byte (TOS<7:0>) 0000 0000 37
STKPTR STKFUL STKUNF — Return Stack Pointer 00-0 0000 38
PCLATU
— — — Holding Register for PC<20:16> ---0 0000 39
PCLATH Holding Register for PC<15:8> 0000 0000 39
PCL PC Low Byte (PC<7:0>) 0000 0000 39
TBLPTRU
— —bit21
(2)
Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) --00 0000 58
TBLPTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) 0000 0000 58
TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 0000 0000 58
TABLAT Program Memory Table Latch 0000 0000 58
PRODH Product Register High Byte xxxx xxxx 71
PRODL Product Register Low Byte xxxx xxxx 71
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 75
INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2
—TMR0IP—RBIP1111 -1-1 76
INTCON3 INT2IP INT1IP
— INT2IE INT1IE — INT2IF INT1IF 11-0 0-00 77
INDF0 Uses contents of FSR0 to address data memory - value of FSR0 not changed (not a physical register) n/a 50
POSTINC0 Uses contents of FSR0 to address data memory - value of FSR0 post-incremented (not a physical register) n/a 50
POSTDEC0 Uses contents of FSR0 to address data memory - value of FSR0 post-decremented (not a physical register) n/a 50
PREINC0 Uses contents of FSR0 to address data memory - value of FSR0 pre-incremented (not a physical register) n/a 50
PLUSW0 Uses contents of FSR0 to address data memory - value of FSR0 (not a physical register).
Offset by value in WREG.
n/a 50
FSR0H
— — — — Indirect Data Memory Address Pointer 0 High Byte ---- 0000 50
FSR0L Indirect Data Memory Address Pointer 0 Low Byte xxxx xxxx 50
WREG Working Register xxxx xxxx n/a
INDF1 Uses contents of FSR1 to address data memory - value of FSR1 not changed (not a physical register) n/a 50
POSTINC1 Uses contents of FSR1 to address data memory - value of FSR1 post-incremented (not a physical register) n/a 50
POSTDEC1 Uses contents of FSR1 to address data memory - value of FSR1 post-decremented (not a physical register) n/a 50
PREINC1 Uses contents of FSR1 to address data memory - value of FSR1 pre-incremented (not a physical register) n/a 50
PLUSW1 Uses contents of FSR1 to address data memory - value of FSR1 (not a physical register).
Offset by value in WREG.
n/a 50
FSR1H
— — — — Indirect Data Memory Address Pointer 1 High Byte ---- 0000 50
FSR1L Indirect Data Memory Address Pointer 1 Low Byte xxxx xxxx 50
BSR
— — — — Bank Select Register ---- 0000 49
INDF2 Uses contents of FSR2 to address data memory - value of FSR2 not changed (not a physical register) n/a 50
POSTINC2 Uses contents of FSR2 to address data memory - value of FSR2 post-incremented (not a physical register) n/a 50
POSTDEC2 Uses contents of FSR2 to address data memory - value of FSR2 post-decremented (not a physical register) n/a 50
PREINC2 Uses contents of FSR2 to address data memory - value of FSR2 pre-incremented (not a physical register) n/a 50
PLUSW2 Uses contents of FSR2 to address data memory - value of FSR2 (not a physical register).
Offset by value in WREG.
n/a 50
FSR2H
— — — — Indirect Data Memory Address Pointer 2 High Byte ---- 0000 50
FSR2L Indirect Data Memory Address Pointer 2 Low Byte xxxx xxxx 50
STATUS
— — —NOVZDCC---x xxxx 52
TMR0H Timer0 Register High Byte 0000 0000 105
TMR0L Timer0 Register Low Byte xxxx xxxx 105
T0CON TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 1111 1111 103
Legend: x = unknown, u = unchanged, - = unimplemented, q = value depends on condition
Note 1: RA6 and associated bits are configured as port pins in RCIO and ECIO Oscillator mode only and read '0' in all other Oscillator modes.
2: Bit 21 of the TBLPTRU allows access to the device configuration bits.
3: These registers and bits are reserved on the PIC18F2X2 devices; always maintain these clear.