Datasheet
2010 Microchip Technology Inc. DS39616D-page 335
PIC18F2331/2431/4331/4431
Supply Current (IDD)
(2,3)
PIC18LF2X31/4X31 150 250 A -40°C
V
DD = 2.0V
F
OSC = 1 MHZ
(PRI_RUN,
EC oscillator)
150 250 A+25°C
160 250 A+85°C
PIC18LF2X31/4X31 340 350 A -40°C
V
DD = 3.0V300 350 A+25°C
280 350 A+85°C
All devices 0.72 1.0 mA -40°C
V
DD = 5.0V
0.63 1.0 mA +25°C
0.57 1.0 mA +85°C
0.9 2.1 mA +125°C
PIC18LF2X31/4X31 440 600 A -40°C
V
DD = 2.0V
F
OSC = 4 MHz
(PRI_RUN,
EC oscillator)
450 600 A+25°C
460 600 A+85°C
PIC18LF2X31/4X31 0.80 1.0 mA -40°C
V
DD = 3.0V0.78 1.0 mA +25°C
0.77 1.0 mA +85°C
All devices 1.6 2.0 mA -40°C
V
DD = 5.0V
1.5 2.0 mA +25°C
1.5 2.0 mA +85°C
2.0 4.2 mA +125°C
All devices
10 28 mA +125°C V
DD = 5.0V
F
OSC = 25 MHz
(PRI_RUN,
EC oscillator)
All devices 9.5 12 mA -40°C
V
DD = 4.2V
F
OSC = 40 MHZ
(PRI_RUN,
EC oscillator)
9.7 12 mA +25°C
9.9 12 mA +85°C
All devices 11.9 15 mA -40°C
V
DD = 5.0V12.1 15 mA +25°C
12.3 15 mA +85°C
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F2331/2431/4331/4431 (Industrial, Extended)
PIC18LF2331/2431/4331/4431 (Industrial) (Continued)
PIC18LF2331/2431/4331/4431
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
PIC18F2331/2431/4331/4431
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD or VSS, and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be estimated
by the formula: Ir = V
DD/2REXT (mA) with REXT in k.
4: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.