Datasheet

 2010 Microchip Technology Inc. Preliminary DS39964B-page 403
PIC18F47J53 FAMILY
23.7 Oscillator
The USB module has specific clock requirements. For
full-speed operation, the clock source must be 48 MHz.
Even so, the microcontroller core and other peripherals
are not required to run at that clock speed. Available
clocking options are described in detail in Section 3.3
“Oscillator Settings for USB”.
23.8 USB Firmware and Drivers
Microchip provides a number of application-specific
resources, such as USB firmware and driver support.
Refer to www.microchip.com for the latest firmware and
driver support.
TABLE 23-4: REGISTERS ASSOCIATED WITH USB MODULE OPERATION
(1)
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
INTCON GIE/GIEH PEIE/GIEL
TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF
IPR2
OSCFIP CM2IP CM1IP USBIP BCL1IP HLVDIP TMR3IP CCP2IP
PIR2
OSCFIF CM2IF CM1IF USBIF BCL1IF HLVDIF TMR3IF CCP2IF
PIE2
OSCFIE CM2IE CM1IE USBIE BCL1IE HLVDIE TMR3IE CCP2IE
UCON
— PPBRST SE0 PKTDIS USBEN RESUME SUSPND —
UCFG UTEYE UOEMON
— UPUEN UTRDIS FSEN PPB1 PPB0
USTAT
— ENDP3 ENDP2 ENDP1 ENDP0 DIR PPBI —
UADDR
— ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0
UFRML FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0
UFRMH
— — — — —FRM10FRM9FRM8
UIR
— SOFIF STALLIF IDLEIF TRNIF ACTVIF UERRIF URSTIF
UIE
— SOFIE STALLIE IDLEIE TRNIE ACTVIE UERRIE URSTIE
UEIR BTSEF
— — BTOEF DFN8EF CRC16EF CRC5EF PIDEF
UEIE BTSEE
— — BTOEE DFN8EE CRC16EE CRC5EE PIDEE
UEP0
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP1
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP2
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP3
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP4
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP5
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP6
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP7
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP8
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP9
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP10
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP11
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP12
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP13
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP14
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
UEP15
— — — EPHSHK EPCONDIS EPOUTEN EPINEN EPSTALL
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used by the USB module.
Note 1: This table includes only those hardware mapped SFRs located in Bank 15 of the data memory space. The Buffer
Descriptor registers, which are mapped into Bank 4 and are not true SFRs, are listed separately in Table 23-3.