Datasheet

PIC18F66K80 FAMILY
DS39977F-page 554  2010-2012 Microchip Technology Inc.
Module Differential Currents (IWDT, IBOR, IHLVD, IADC)
D022
IWDT)
Watchdog Timer
PIC18LFXXK80 0.4 2 A -40°C to +125°C VDD = 1.8V
Regulator Disabled
PIC18
LFXXK80 0.6 3 A -40°C to +125°C VDD = 3.3V
Regulator Disabled
PIC18FXXK80 0.6 3 A -40°C to +125°C VDD = 3.3V
Regulator Enabled
PIC18FXXK80 0.8 4 A -40°C to +125°C VDD = 5.5V
Regulator Enabled
D022A
IBOR)
Brown-out Reset
PIC18LFXXK80 4.6 20 A -40°C to +125°C VDD = 1.8V
Regulator Disabled
High-Power BOR
PIC18FXXK80 4.6 20 A -40°C to +125°C VDD = 3.3V
Regulator Enabled
PIC18FXXK80 4.6 20 A -40°C to +125°C VDD = 5.5V
Regulator Enabled
D022B
IHLVD
High/Low-Voltage Detect
PIC18LFXXK80 3.8 10 A -40°C to +125°C VDD = 1.8V
Regulator Disabled
PIC18LFXXK80 4.5 12 A -40°C to +125°C VDD = 3.3V
Regulator Disabled
PIC18FXXK80 3.8 12 A -40°C to +125°C VDD = 3.3V
Regulator Enabled
PIC18FXXK80 4.9 13 A -40°C to +125°C VDD = 5.5V
Regulator Enabled
D026
IADC
A/D Converter
PIC18LFXXK80 0.4 1.5 -40°C to +125°C VDD = 1.8V
Regulator Disabled
A/D on, not converting
PIC18L
FXXK80 0.5 2 A -40°C to +125°C VDD = 3.3V
Regulator Disabled
PIC18FXXK80 0.5 3 A -40°C to +125°C VDD = 3.3V
Regulator Enabled
PIC18FXXK80 1 3 A -40°C to +125°C VDD = 5.5V
Regulator Enabled
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F66K80 Family (Industrial/Extended) (Continued)
PIC18F66K80 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C
 TA  +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend:
Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the
part in Sleep mode, with all I/O pins in a high-impedance state and tied to V
DD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the
current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR = VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: For LF devices, RETEN (CONFIG1L<0>) = 1.
5: For F devices, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0.