Datasheet

PIC18F2XK20/4XK20
DS41303G-page 128  2010 Microchip Technology Inc.
TABLE 10-5: PORTC I/O SUMMARY
Pin Function
TRIS
Setting
I/O
I/O
Type
Description
RC0/T1OSO/
T13CKI
RC0 0 O DIG LATC<0> data output.
1 I ST PORTC<0> data input.
T1OSO x O ANA Timer1 oscillator output; enabled when Timer1 oscillator enabled.
Disables digital I/O.
T13CKI 1 I ST Timer1/Timer3 counter input.
RC1/T1OSI/CCP2 RC1 0 O DIG LATC<1> data output.
1 I ST PORTC<1> data input.
T1OSI x I ANA Timer1 oscillator input; enabled when Timer1 oscillator enabled.
Disables digital I/O.
CCP2
(1)
0 O DIG CCP2 compare and PWM output; takes priority over port data.
1 I ST CCP2 capture input.
RC2/CCP1/P1A RC2 0 O DIG LATC<2> data output.
1 I ST PORTC<2> data input.
CCP1 0 O DIG ECCP1 compare or PWM output; takes priority over port data.
1 I ST ECCP1 capture input.
P1A 0 O DIG ECCP1 Enhanced PWM output, channel A. May be configured for
tri-state during Enhanced PWM shutdown events. Takes priority over
port data.
RC3/SCK/SCL RC3 0 O DIG LATC<3> data output.
1 I ST PORTC<3> data input.
SCK 0 O DIG SPI clock output (MSSP module); takes priority over port data.
1 I ST SPI clock input (MSSP module).
SCL 0 ODIGI
2
C™ clock output (MSSP module); takes priority over port data.
1 II
2
C/SMB I
2
C clock input (MSSP module); input type depends on module setting.
RC4/SDI/SDA RC4 0 O DIG LATC<4> data output.
1 I ST PORTC<4> data input.
SDI 1 I ST SPI data input (MSSP module).
SDA 1 ODIGI
2
C data output (MSSP module); takes priority over port data.
1 II
2
C/SMB I
2
C data input (MSSP module); input type depends on module setting.
RC5/SDO RC5 0 O DIG LATC<5> data output.
1 I ST PORTC<5> data input.
SDO 0 O DIG SPI data output (MSSP module); takes priority over port data.
RC6/TX/CK RC6 0 O DIG LATC<6> data output.
1 I ST PORTC<6> data input.
TX 1 O DIG Asynchronous serial transmit data output (USART module); takes
priority over port data. User must configure as output.
CK 1 O DIG Synchronous serial clock output (USART module); takes priority over
port data.
1 I ST Synchronous serial clock input (USART module).
RC7/RX/DT RC7 0 O DIG LATC<7> data output.
1 I ST PORTC<7> data input.
RX 1 I ST Asynchronous serial receive data input (USART module).
DT 1 O DIG Synchronous serial data output (USART module); takes priority over
port data.
1 I ST Synchronous serial data input (USART module). User must configure
as an input.
Legend: DIG = Digital level output; TTL = TTL input buffer; ST = Schmitt Trigger input buffer; ANA = Analog level input/output;
I
2
C/SMB = I
2
C/SMBus input buffer; x = Don’t care (TRIS bit does not affect port direction or is overridden for this option).
Note 1: Default assignment for CCP2 when the CCP2MX Configuration bit is set. Alternate assignment is RB3.