Datasheet

PIC18(L)F2X/4XK22
DS41412F-page 438  2010-2012 Microchip Technology Inc.
27.6 DC Characteristics: Primary Idle Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
PIC18F2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
Param
No.
Device Characteristics Typ Max Units Conditions
D100 Supply Current (I
DD)
(1),(2)
0.030 0.050 mA -40°C to +125°C VDD = 1.8V Fosc = 1 MHz
(PRI_IDLE mode,
ECM source)
D101
0.045 0.065 mA -40°C to +125°C V
DD = 3.0V
D102
0.06 0.12 mA -40°C to +125°C VDD = 2.3V Fosc = 1 MHz
(PRI_IDLE mode,
ECM source)
D103
0.08 0.15 mA -40°C to +125°C VDD = 3.0V
D104
0.13 0.20 mA -40°C to +125°C VDD = 5.0V
D105
0.45 0.8 mA -40°C to +125°C V
DD = 1.8V Fosc = 20 MHz
(PRI_IDLE mode,
ECH source)
D106
0.70 1.0 mA -40°C to +125°C V
DD = 3.0V
D107
0.55 0.8 mA -40°C to +125°C VDD = 2.3V Fosc = 20 MHz
(PRI_IDLE mode,
ECH source)
D108
0.75 1.0 mA -40°C to +125°C VDD = 3.0V
D109
0.90 1.2 mA -40°C to +125°C VDD = 5.0V
D110
2.25 3.0 mA -40°C to +125°C V
DD = 3.0V Fosc = 64 MHz
(PRI_IDLE mode,
ECH source)
D111
2.25 3.0 mA -40°C to +125°C VDD = 3.0V Fosc = 64 MHz
(PRI_IDLE mode,
ECH source)
D112
2.60 3.5 mA -40°C to +125°C VDD = 5.0V
D113
0.35 0.6 mA -40°C to +125°C V
DD = 1.8V Fosc = 4 MHz
16 MHz Internal
(PRI_IDLE mode,
ECM + PLL source)
D114
0.55 0.8 mA -40°C to +125°C V
DD = 3.0V
D115
0.45 0.6 mA -40°C to +125°C VDD = 2.3V Fosc = 4 MHz
16 MHz Internal
(PRI_IDLE mode,
ECM + PLL source)
D116
0.60 0.9 mA -40°C to +125°C VDD = 3.0V
D117
0.70 1.0 mA -40°C to +125°C VDD = 5.0V
D118
2.2 3.0 mA -40°C to +125°C VDD = 3.0V Fosc = 16 MHz
64 MHz Internal
(PRI_IDLE mode,
ECH + PLL source)
D119
2.2 3.0 mA -40°C to +125°C VDD = 3.0V Fosc = 16 MHz
64 MHz Internal
(PRI_IDLE mode,
ECH + PLL source)
D120
2.5 3.5 mA -40°C to +125°C VDD = 5.0V
Note 1: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
Test condition: All Peripheral Module Control bits in PMD0, PMD1 and PMD2 set to ‘1’.
2: The test conditions for all I
DD measurements in active operation mode are:
All I/O pins set as outputs driven to Vss;
MCLR
= VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI_IDLE only).