Datasheet

 2010-2012 Microchip Technology Inc. DS41412F-page 437
PIC18(L)F2X/4XK22
27.5 DC Characteristics: Primary Run Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
PIC18F2X/4XK22 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
Param
No.
Device Characteristics Typ Max Units Conditions
D070 Supply Current (I
DD)
(1),(2)
0.11 0.20 mA -40°C to +125°C VDD = 1.8V FOSC = 1 MHz
(PRI_RUN mode,
ECM source)
D071
0.17 0.25 mA -40°C to +125°C V
DD = 3.0V
D072
0.15 0.25 mA -40°C to +125°C VDD = 2.3V FOSC = 1 MHz
(PRI_RUN mode,
ECM source)
D073
0.20 0.30 mA -40°C to +125°C VDD = 3.0V
D074
0.25 0.35 mA -40°C to +125°C VDD = 5.0V
D075
1.45 2.0 mA -40°C to +125°C V
DD = 1.8V FOSC = 20 MHz
(PRI_RUN mode,
ECH source)
D076
2.60 3.5 mA -40°C to +125°C V
DD = 3.0V
D077
1.95 2.5 mA -40°C to +125°C VDD = 2.3V FOSC = 20 MHz
(PRI_RUN mode,
ECH source)
D078
2.65 3.5 mA -40°C to +125°C VDD = 3.0V
D079
2.95 4.5 mA -40°C to +125°C VDD = 5.0V
D080
7.5 10 mA -40°C to +125°C V
DD = 3.0V FOSC = 64 MHz
(PRI_RUN,
ECH oscillator)
D081
7.5 10 mA -40°C to +125°C VDD = 3.0V FOSC = 64 MHz
(PRI_RUN mode,
ECH source)
D082
8.5 11.5 mA -40°C to +125°C VDD = 5.0V
D083
1.0 1.5 mA -40°C to +125°C V
DD = 1.8V FOSC = 4 MHz
16 MHz Internal
(PRI_RUN mode,
ECM + PLL source)
D084
1.8 3.0 mA -40°C to +125°C V
DD = 3.0V
D085
1.4 2.0 mA -40°C to +125°C VDD = 2.3V FOSC = 4 MHz
16 MHz Internal
(PRI_RUN mode,
ECM + PLL source)
D086
1.85 2.5 mA -40°C to +125°C VDD = 3.0V
D087
2.1 3.0 mA -40°C to +125°C VDD = 5.0V
D088
6.35 9.0 mA -40°C to +125°C VDD = 3.0V FOSC = 16 MHz
64 MHz Internal
(PRI_RUN mode,
ECH + PLL source)
D089
6.35 9.0 mA -40°C to +125°C VDD = 3.0V FOSC = 16 MHz
64 MHz Internal
(PRI_RUN mode,
ECH + PLL source)
D090
7.0 10 mA -40°C to +125°C VDD = 5.0V
Note 1: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
Test condition: All Peripheral Module Control bits in PMD0, PMD1 and PMD2 set to ‘1’.
2: The test conditions for all I
DD measurements in active operation mode are:
All I/O pins set as outputs driven to Vss;
MCLR
= VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI_IDLE only).