Datasheet
PIC18F/LF1XK50
DS41350E-page 372 Preliminary 2010 Microchip Technology Inc.
27.3 DC Characteristics: PIC18F/LF1XK50-I/E (Power-Down)
PIC18LF1XK50
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC18F1XK50
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Characteristics Min Typ†
Max
+85°C
Max
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D027 — 0.024 0.7 6.7 A 1.8 WDT, BOR, FVR, Voltage
Regulator and T1OSC disabled,
all Peripherals Inactive
— 0.078 1.9 8.5 A3.0
D027 — 6.0 7.0 13 A 1.8 WDT, BOR, FVR and T1OSC
disabled, all Peripherals Inactive
— 7.0 10 15 A 3.0
— 8.0 12 19 A 5.0
Power-down Module Current
D028 — 0.45 1.3 4.4 A 1.8 LPWDT Current
(1)
— 0.75 2.0 6.0 A3.0
D028 — 6.5 7.0 10.5 A 1.8 LPWDT Current
(1)
— 9.6 10.6 17.6 A 3.0
— 10.5 16.5 20 A 5.0
D029 — 12 17 23 A 1.8 FVR current
(3)
—22 19 25 A3.0
D029 — 28 42 50 A 1.8 FVR current
(3, 5)
— 35.6 45.6 55 A 3.0
— 38.5 49 60 A 5.0
D030 — — 21 27 A 3.0 BOR Current
(1, 3)
D030 — 27 48 51 A 3.0 BOR Current
(1, 3, 5)
— 36.5 51 55 A 5.0
D031 — 0.79 3.6 5.3 A 1.8 T1OSC Current
(1)
— 1.8 2.9 6.9 A3.0
D031 — 8.0 7.5 10 A 1.8 T1OSC Current
(1)
— 8.5 10.5 15 A 3.0
— 10.5 12.5 24 A 5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: Fixed Voltage Reference is automatically enabled whenever the BOR is enabled
4: A/D oscillator source is F
RC
5: 330 f capacitor on VUSB pin.