Datasheet

PIC18F1220/1320
DS39605F-page 246 © 2007 Microchip Technology Inc.
Supply Current (I
DD)
(2,3)
PIC18LF1220/1320 35 50 μA -40°C
F
OSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
35 50 μA+25°C V
DD = 2.0V
35 60 μA+85°C
PIC18LF1220/1320 55 80 μA -40°C
50 80 μA+25°C V
DD = 3.0V
60 100 μA+85°C
All devices 105 150 μA -40°C
V
DD = 5.0V
110 150 μA+25°C
115 150 μA+85°C
Extended devices 125 300 μA +125°C
PIC18LF1220/1320 135 180 μA -40°C
F
OSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
140 180 μA+25°C V
DD = 2.0V
140 180 μA+85°C
PIC18LF1220/1320 215 280 μA -40°C
225 280 μA+25°C V
DD = 3.0V
230 280 μA+85°C
All devices 410 525 μA -40°C
V
DD = 5.0V
420 525 μA+25°C
430 525 μA+85°C
Extended devices 450 800 μA +125°C
Extended devices 2.2 3.0 mA +125°C V
DD = 4.2V FOSC = 25 MHz
(PRI_IDLE mode,
EC oscillator)
2.7 3.5 mA +125°C V
DD = 5.0V
22.2 DC Characteristics: Power-Down and Supply Current
PIC18F1220/1320 (Industrial)
PIC18LF1220/1320 (Industrial) (Continued)
PIC18LF1220/1320
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
PIC18F1220/1320
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD or VSS and all features that add delta
current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR
= VDD; WDT enabled/disabled as specified.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be estimated
by the formula Ir = V
DD/2REXT (mA) with REXT in kΩ.
4: Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.