Datasheet
PIC18CXX2
DS39026D-page 238 1999-2013 Microchip Technology Inc.
IDD Supply Current
(2,4)
D010 PIC18LCXX2 — — 2 mA XT, RC, RCIO osc configurations
F
OSC = 4 MHz, VDD = 2.5V
D010 PIC18CXX2 — — 4 mA XT, RC, RCIO osc configurations
F
OSC = 4 MHz, VDD = 4.2V
D010A PIC18LCXX2 — — 55 A LP osc configuration
F
OSC = 32 kHz, VDD = 2.5V
D010A PIC18CXX2 — — 250 A LP osc configuration
F
OSC = 32 kHz, VDD = 4.2V
D010C PIC18LCXX2 — — 38 mA EC, ECIO osc configurations
F
OSC = 40 MHz, VDD = 5.5V
D010C PIC18CXX2 — — 38 mA EC, ECIO osc configurations
F
OSC = 40 MHz, VDD = 5.5V
D013 PIC18LCXX2
—
—
—
—
—
—
3.5
25
38
mA
mA
mA
HS osc configuration
F
OSC = 6 MHz, VDD = 2.5V
F
OSC = 25 MHz, VDD = 5.5V
HS + PLL osc configurations
FOSC = 10 MHz, VDD = 5.5V
D013 PIC18CXX2
—
—
—
—
25
38
mA
mA
HS osc configuration
F
OSC = 25 MHz, VDD = 5.5V
HS + PLL osc configurations
FOSC = 10 MHz, VDD = 5.5V
D014 PIC18LCXX2
——55A
Timer1 osc configuration
F
OSC = 32 kHz, VDD = 2.5V
D014 PIC18CXX2
—
—
—
—
200
250
A
A
OSCB osc configuration
F
OSC = 32 kHz, VDD = 4.2V, -40C to +85C
F
OSC = 32 kHz, VDD = 4.2V, -40C to +125C
Legend: Shading of rows is to assist in readability of the table.
Note 1: This is the limit to which V
DD can be lowered in SLEEP mode, or during a device RESET, without losing RAM
data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an
impact on the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD
MCLR
= VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
DD or VSS, and all fea-
tures that add delta current disabled (such as WDT, Timer1 Oscillator, BOR,...).
4: For RC osc configuration, current through R
EXT is not included. The current through the resistor can be
estimated by the formula Ir = V
DD/2REXT (mA) with REXT in kOhm.
21.1 DC Characteristics (Continued)
PIC18LCXX2
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
PIC18CXX2
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Symbol Characteristic Min Typ Max Units Conditions