Datasheet

 1998-2013 Microchip Technology Inc. DS30289C-page 245
PIC17C7XX
Input Leakage Current
(Notes 2, 3)
D060 I
IL I/O ports (except RA2, RA3) – – 1 AVss VPIN VDD,
I/O Pin (in digital mode) at
hi-impedance PORTB
weak pull-ups disabled
D061 MCLR
, TEST – – 2 AVPIN =Vss orVPIN =VDD
D062 RA2, RA3 2 AVss VRA2, VRA3  12V
D063 OSC1 (EC, RC modes) – – 1 AVss VPIN VDD
D063B OSC1 (XT, LF modes) – – VPIN ARF  1 M
D064 MCLR
, TEST – – 25 AVMCLR = VPP = 12V
(when not programming)
D070 IPURB PORTB Weak Pull-up Current 85 130 260 A VPIN = VSS, RBPU = 0
4.5V V
DD 5.5V
Output Low Voltage
D080
D081
V
OL I/O ports
with TTL buffer
–
–
–
–
–
–
0.1V
DD
0.1VDD
0.4
V
V
V
I
OL = VDD/1.250 mA
4.5V  V
DD  5.5V
V
DD  3.0V
I
OL = 6 mA, VDD = 4.5V
(Note 6)
D082 RA2 and RA3 –
–
–
–
3.0
0.6
V
V
I
OL = 60.0 mA, VDD = 5.5V
I
OL = 60.0 mA, VDD = 4.5V
D083
D084
OSC2/CLKOUT
(RC and EC osc modes)
–
–
–
–
0.4
0.1V
DD
V
V
IOL = 1 mA, VDD = 4.5V
I
OL = VDD/5 mA
(PIC17LC7XX only)
Output High Voltage (Note 3)
D090
D091
V
OH I/O ports (except RA2 and
RA3)
with TTL buffer
0.9V
DD
0.9V
DD
2.4
–
–
–
–
–
–
V
V
V
I
OH = -VDD/2.5 mA
4.5V  V
DD  5.5V
V
DD  3.0V
I
OH = -6.0 mA, VDD =4.5V
(Note 6)
D093
D094
OSC2/CLKOUT
(RC and EC osc modes)
2.4
0.9V
DD
–
–
–
–
V
V
IOH = -5 mA, VDD = 4.5V
I
OH = -VDD/5 mA
(PIC17LC7XX only)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  T
A  +125°C for extended
-40°C  T
A  +85°C for industrial
0°C  T
A  +70°C for commercial
Operating voltage V
DD range as described in Section 20.1
Param.
No.
Sym Characteristic Min Typ† Max Units Conditions
† Data in “Typ” column is at 5V, 25C unless otherwise stated.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC17CXXX devices be driven with external clock in RC mode.
2: The leakage current on the MCLR
pin is strongly dependent on the applied voltage level. Higher leakage
current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.
4: These specifications are for the programming of the on-chip program memory EPROM through the use of the
table write instructions. The complete programming specifications can be found in: PIC17C7XX Programming
Specifications (Literature number DS TBD).
5: The MCLR
/VPP pin may be kept in this range at times other than programming, but is not recommended.
6: For TTL buffers, the better of the two specifications may be used.