Datasheet

PIC16F913/914/916/917/946
DS41250F-page 228 © 2007 Microchip Technology Inc.
LVDCON 109h --00 -100 --00 -100 --uu -uuu
EEDATL 10Ch 0000 0000 0000 0000 uuuu uuuu
EEADRL 10Dh 0000 0000 0000 0000 uuuu uuuu
EEDATH 10Eh --00 0000 0000 0000 uuuu uuuu
EEADRH 10Fh ---0 0000 0000 0000 uuuu uuuu
LCDDATA0 110h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA1 111h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA2
(6)
112h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA3 113h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA4 114h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA5
(6)
115h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA6 116h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA7 117h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA8
(6)
118h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA9 119h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA10 11Ah xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA11
(6)
11Bh xxxx xxxx uuuu uuuu uuuu uuuu
LCDSE0 11Ch 0000 0000 uuuu uuuu uuuu uuuu
LCDSE1 11Dh 0000 0000 uuuu uuuu uuuu uuuu
LCDSE2
(6)
11Eh 0000 0000 uuuu uuuu uuuu uuuu
TRISF
(7)
185h 1111 1111 1111 1111 uuuu uuuu
TRISG
(7)
187h --11 1111 --11 1111 --uu uuuu
PORTF
(7)
188h xxxx xxxx 0000 0000 uuuu uuuu
PORTG
(7)
189h --xx xxxx --00 0000 --uu uuuu
LCDDATA12
(7)
190h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA13
(7)
191h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA14
(7)
192h ---- --xx ---- --uu ---- --uu
LCDDATA15
(7)
193h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA16
(7)
194h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA17
(7)
195h ---- --xx ---- --uu ---- --uu
LCDDATA18
(7)
196h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA19
(7)
197h xxxx xxxx uuuu uuuu uuuu uuuu
LCDDATA20
(7)
198h ---- --xx ---- --uu ---- --uu
LCDDATA21
(7)
199h xxxx xxxx uuuu uuuu uuuu uuuu
TABLE 16-4: INITIALIZATION CONDITION FOR REGISTERS (CONTINUED)
Register Address Power-on Reset
• MCLR
Reset
• WDT Reset
• Brown-out Reset
(1)
• Wake-up from Sleep
through interrupt
• Wake-up from Sleep
through WDT time-out
Legend: u = unchanged, x = unknown,
- = unimplemented bit, reads as ‘0’, q = value depends on condition.
Note 1: If VDD goes too low, Power-on Reset will be activated and registers will be affected differently.
2: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up).
3: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt
vector (0004h).
4: See Table 16-5 for Reset value for specific condition.
5: If Reset was due to brown-out, then bit 0 = 0. All other Resets will cause bit 0 = u.
6: PIC16F914/917 and PIC16F946 only.
7: PIC16F946 only.