Datasheet
2006-2012 Microchip Technology Inc. DS41291G-page 255
PIC16F882/883/884/886/887
17.5 DC Characteristics: PIC16F882/883/884/886/887-I (Industrial)
PIC16F882/883/884/886/887-E (Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Sym. Characteristic Min. Typ† Max. Units Conditions
V
IL Input Low Voltage
I/O Port:
D030 with TTL buffer Vss — 0.8 V 4.5V V
DD 5.5V
D030A Vss — 0.15 V
DD V2.0V VDD 4.5V
D031 with Schmitt Trigger buf-
fer
Vss — 0.2 VDD V2.0V VDD 5.5V
D032 MCLR
, OSC1 (RC mode)
(1)
VSS —0.2 VDD V
D033 OSC1 (XT and LP modes) V
SS —0.3V
D033A OSC1 (HS mode) VSS —0.3 VDD V
V
IH Input High Voltage
I/O ports: —
D040 with TTL buffer 2.0 — V
DD V4.5V VDD 5.5V
D040A 0.25 VDD + 0.8 — VDD V2.0V VDD 4.5V
D041 with Schmitt Trigger buffer 0.8 V
DD —VDD V2.0V VDD 5.5V
D042 MCLR 0.8 VDD —VDD V
D043 OSC1 (XT and LP modes) 1.6 — V
DD V
D043A OSC1 (HS mode) 0.7 VDD —VDD V
D043B OSC1 (RC mode) 0.9 V
DD —VDD V (Note 1)
IIL Input Leakage Current
(2)
D060 I/O ports — 0.1 1 AVSS VPIN VDD,
Pin at high-impedance
D061 MCLR
(3)
— 0.1 5 AVSS VPIN VDD
D063 OSC1 — 0.1 5 AVSS VPIN VDD, XT, HS and
LP oscillator configuration
D070* I
PUR PORTB Weak Pull-up Cur-
rent
50 250 400 AVDD = 5.0V, VPIN = VSS
VOL Output Low Voltage
(5)
D080 I/O ports — — 0.6 V IOL = 8.5 mA, VDD = 4.5V
(Ind.)
V
OH Output High Voltage
(5)
D090 I/O ports VDD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V
(Ind.)
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an
external clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR
pin is strongly dependent on the applied voltage level. The specified levels
represent normal operating conditions. Higher leakage current may be measured at different input voltages.
4: See Section 10.3.1 “Using the Data EEPROM” for additional information.
5: Including OSC2 in CLKOUT mode.