Manualshelf

Datasheet

ManualsBrandsMICROCHIP TECHNOLOGY ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller SSOP 28 8-Bit 20 MHz I/O number 22
11121314151617181920
PIC16F7X
DS30325B-page 12 2002 Microchip Technology Inc.
PORTD is a bi-directional I/O port or parallel slave port
when interfacing to a microprocessor bus.
RD0/PSP0
RD0
PSP0
19 21 38
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD1/PSP1
RD1
PSP1
20 22 39 I
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD2/PSP2
RD2
PSP2
21 23 40 I
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD3/PSP3
RD3
PSP3
22 24 41
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD4/PSP4
RD4
PSP4
27 30 2
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD5/PSP5
RD5
PSP5
28 31 3
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD6/PSP6
RD6
PSP6
29 32 4
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
RD7/PSP7
RD7
PSP7
30 33 5
I/O
I/O
ST/TTL
(3)
Digital I/O.
Parallel Slave Port data.
PORTE is a bi-directional I/O port.
RE0/RD
/AN5
RE0
RD
AN5
8925
I/O
I
I
ST/TTL
(3)
Digital I/O.
Read control for parallel slave port .
Analog input 5.
RE1/WR
/AN6
RE1
WR
AN6
91026
I/O
I
I
ST/TTL
(3)
Digital I/O.
Write control for parallel slave port .
Analog input 6.
RE2/CS
/AN7
RE2
CS
AN7
10 11 27
I/O
I
I
ST/TTL
(3)
Digital I/O.
Chip select control for parallel slave port .
Analog input 7.
V
SS 12,31 13,34 6,29 P — Ground reference for logic and I/O pins.
V
DD 11,32 12,35 7,28 P — Positive supply for logic and I/O pins.
NC — 1,17,2
8, 40
12,13,
33, 34
— These pins are not internally connected. These pins should
be left unconnected.
TABLE 1-3: PIC16F74 AND PIC16F77 PINOUT DESCRIPTION (CONTINUED)
Pin Name
DIP
Pin#
PLCC
Pin#
QFP
Pin#
I/O/P
Type
Buffer
Type
Description
Legend: I = input O = output I/O = input/output P = power
— = Not used TTL = TTL input ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured as an external interrupt.
2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.
3: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel
Slave Port mode (for interfacing to a microprocessor bus).
4: This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.