Datasheet
© 2009 Microchip Technology Inc. DS41341E-page 217
PIC16F72X/PIC16LF72X
Power-down Base Current (IPD)
(2)
D027 — 0.06 0.7 5.0 μA 1.8 A/D Current (Note 1, Note 4), no
conversion in progress
— 0.08 1.0 5.5 μA3.0
D027 — 6 10.7 18 μA 1.8 A/D Current (Note 1, Note 4), no
conversion in progress
— 7 10.6 20 μA 3.0
— 7.2 11.9 22 μA 5.0
D027A — 250 400 — μA 1.8 A/D Current (Note 1, Note 4),
conversion in progress
— 250 400 — μA3.0
D027A — 280 430 — μA 1.8 A/D Current (Note 1, Note 4,
Note 5), conversion in progress
— 280 430 — μA 3.0
— 280 430 — μA 5.0
D028 — 2.2 3.2 14.4 μA 1.8 Cap Sense Low Power
Oscillator mode
—3.34.415.6μA3.0
D028 — 6.5 13 21 μA 1.8 Cap Sense Low Power
Oscillator mode
— 8 14 23 μA 3.0
— 8 14 25 μA 5.0
D028A — 4.2 6 17 μA 1.8 Cap Sense Medium Power
Oscillator mode
—6 7 18μA3.0
D028A — 8.5 15.5 23 μA 1.8 Cap Sense Medium Power
Oscillator mode
— 11 17 24 μA 3.0
— 11 18 27 μA 5.0
D028B — 12 14 25 μA 1.8 Cap Sense High Power
Oscillator mode
—32 35 44 μA3.0
D028B — 16 20 31 μA 1.8 Cap Sense High Power
Oscillator mode
— 36 41 50 μA 3.0
— 42 49 58 μA 5.0
23.3 DC Characteristics: PIC16F72X/PIC16LF72X-I/E (Power-Down) (Continued)
PIC16LF72X
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
PIC16F72X
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral Δ current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: Fixed Voltage Reference is automatically enabled whenever the BOR is enabled
4: A/D oscillator source is F
RC
5: 0.1 μF capacitor on VCAP (RA0).