Datasheet
PIC16(L)F722A/723A
DS41417B-page 204 2010-2012 Microchip Technology Inc.
23.3 DC Characteristics: PIC16(L)F722A/723A-I/E (Power-Down)
PIC16LF722A/723A
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C T
A +125°C for extended
PIC16F722A/723A
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C T
A +85°C for industrial
-40°C T
A +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
Power-down Base Current (I
PD)
(2)
D020 — 0.02 0.7 3.9 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 0.08 1.0 4.3 A3.0
D020 — 4.3 10.2 17 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
— 5 10.5 18 A 3.0
— 5.5 11.8 21 A 5.0
D021 — 0.5 1.7 4.1 A 1.8 LPWDT Current (Note 1)
— 0.8 2.5 4.8 A3.0
D021 — 6 13.5 16.4 A 1.8 LPWDT Current (Note 1)
— 6.5 14.5 16.8 A 3.0
— 7.5 16 18.7 A 5.0
D021A — 8.5 14 19 A 1.8 FVR current (Note 1. Note 3)
— 8.5 14 20 A3.0
D021A — 23 44 48 A 1.8 FVR current (Note 1, Note 3,
Note 5)
— 25 45 55 A 3.0
— 26 60 70 A 5.0
D022 — — — — A 1.8 BOR Current (Note 1, Note 3)
— 7.5 12 22 A3.0
D022 — — — — A 1.8 BOR Current (Note 1, Note 3,
Note 5)
— 23 42 49 A 3.0
— 25 46 50 A 5.0
D026 — 0.6 2 — A 1.8 T1OSC Current (Note 1)
—1.83.0 — A3.0
D026 — 4.5 11.1 — A 1.8 T1OSC Current (Note 1)
— 6 12.5 — A 3.0
— 7 13.5 — A 5.0
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: Fixed Voltage Reference is automatically enabled whenever the BOR is enabled.
4: A/D oscillator source is F
RC.
5: 0.1 F capacitor on V
CAP (RA0).