Datasheet

PIC16F716
DS41206B-page 96 © 2007 Microchip Technology Inc.
12.4 DC Characteristics: PIC16F716 (Industrial, Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Operating voltage V
DD range as described in DC spec Section 12.1 “DC Charac-
teristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Character-
istics: PIC16F716 (Industrial, Extended)”.
Param
No.
Sym Characteristic Min Typ† Max Units Conditions
Input Low Voltage
V
IL I/O ports
D030
D030A
with TTL buffer V
SS
VSS
—
—
0.8
0.15 V
DD
V
V
4.5V ≤ VDD ≤ 5.5V
otherwise
D031 with Schmitt Trigger buffer V
SS — 0.2 VDD V
D032 MCLR
, OSC1 (in RC mode) VSS — 0.2 VDD V
D033 OSC1 (in HS mode)
OSC1 (in XT and LP modes)
V
SS
VSS
—
—
0.3 VDD
0.6
V
V
(Note1)
Input High Voltage
V
IH I/O ports —
D040 with TTL buffer 2.0 — V
DD V4.5V ≤ VDD ≤ 5.5V
D040A 0.25 V
DD +
0.8V
—VDD V otherwise
D041 with Schmitt Trigger buffer 0.8 V
DD —VDD V For entire VDD range
D042 MCLR
0.8 VDD —VDD V
D042A OSC1 (XT, HS and LP modes) 0.7 V
DD —VDD V (Note1)
D043 OSC1 (in RC mode) 0.9 V
DD —VDD V
Input Leakage Current
(2), (3)
D060 IIL I/O ports —
—
—
—
±1
±500
μA
nA
Vss ≤ VPIN ≤ VDD, Pin at
high-impedance
Vss ≤ V
PIN ≤ VDD, Pin configured as
analog input
D061 MCLR
, RA4/T0CKI — — ±5 μA Vss ≤ VPIN ≤ VDD
D063 OSC1/CLKIN — — ±5 μA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
modes
D070 I
PURB PORTB weak pull-up current 50 250 400 μAVDD = 5V, VPIN = VSS
Output Low Voltage
D080 V
OL I/O ports — — 0.6 V IOL = 8.5 mA, VDD = 4.5V, -40°C to
+85°C
——0.6VI
OL = 7.0 mA, VDD = 4.5V, -40°C to
+125°C
D083 OSC2/CLKOUT (RC Osc mode) — — 0.6 V I
OL = 1.6 mA, VDD = 4.5V, -40°C to
+85°C
——0.6VI
OL = 1.2 mA, VDD = 4.5V, -40°C to
+125°C
Output High Voltage
D090 V
OH I/O ports
(3)
VDD-0.7 — — V IOH = -3.0 mA, VDD = 4.5V, -40°C to
+85°C
V
DD-0.7 — — V IOH = -2.5 mA, VDD = 4.5V, -40°C to
+125°C
D092 OSC2/CLKOUT (RC Osc mode) V
DD-0.7 — — V IOH = -1.3 mA, VDD = 4.5V, -40°C to
+85°C
V
DD-0.7 — — V IOH = -1.0 mA, VDD = 4.5V, -40°C to
+125°C
D150* V
OD Open-Drain High Voltage — — 8.5 V RA4 pin
Capacitive Loading Specs on Output Pins
D100 COSC2 OSC2/CLKOUT pin — — 15 pF In XT, HS and LP modes when external
clock is used to drive OSC1.
D101 C
IO All I/O pins and OSC2 (in RC mode) — — 50 pF
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC
®
be driven with
external clock in RC mode.
2: The leakage current on the MCLR
/VPP pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as current sourced by the pin.