Datasheet

 2010 Microchip Technology Inc. DS41326E-page 87
PIC16F526
TABLE 14-1: DC CHARACTERISTICS: PIC16F526 (Industrial, Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating temperature -40°C  T
A  +85°C (industrial)
-40°C  TA  +125°C (extended)
Operating voltage V
DD range as described in DC spec.
Param
No.
Sym. Characteristic Min. Typ.† Max. Units Conditions
V
IL Input Low Voltage
I/O ports
D030 with TTL buffer Vss — 0.8 V For all 4.5  VDD 5.5V
D030A Vss — 0.15 VDD V Otherwise
D031 with Schmitt Trigger buffer Vss — 0.15 VDD V
D032 MCLR, T0CKI Vss — 0.15 VDD V
D033 OSC1 (EXTRC mode), EC
(1)
Vss — 0.15 VDD V
D033 OSC1 (HS mode) Vss — 0.3 VDD V
D033 OSC1 (XT and LP modes) Vss — 0.3 V
VIH Input High Voltage
I/O ports —
D040 with TTL buffer 2.0 — V
DD V4.5  VDD 5.5V
D040A 0.25VDD
+ 0.8V
—V
DD V Otherwise
D041 with Schmitt Trigger buffer 0.85VDD —VDD V For entire VDD range
D042 MCLR, T0CKI 0.85VDD —VDD V
D042A OSC1 (EXTRC mode), EC
(1)
0.85VDD —VDD V
D042A OSC1 (HS mode) 0.7VDD —VDD V
D043 OSC1 (XT and LP modes) 1.6 — VDD V
D070 IPUR PORTB weak pull-up current
(4)
50 250 400 AVDD = 5V, VPIN = VSS
IIL Input Leakage Current
(2,5)
D060 I/O ports — — ±1 AVss VPIN VDD, Pin at high-impedance
D061 RB3/MCLR
(3)
—±0.7±5 AVss VPIN VDD
D063 OSC1 — — ±5 AVss VPIN VDD, XT, HS and LP osc
configuration
VOL Output Low Voltage
D080 I/O ports/CLKOUT — — 0.6 V IOL = 8.5 mA, VDD = 4.5V, –40C to +85C
D080A — — 0.6 V IOL = 7.0 mA, VDD = 4.5V, –40C to +125C
VOH Output High Voltage
D090 I/O ports/CLKOUT V
DD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V, –40C to +85C
D090A V
DD – 0.7 — — V IOH = -2.5 mA, VDD = 4.5V, –40C to +125C
Capacitive Loading Specs on Output Pins
D100
COSC2 OSC2 pin — — 15 pF In XT, HS and LP modes when external clock is
used to drive OSC1.
D101 CIO All I/O pins and OSC2 — — 50 pF
Flash Data Memory
D120 E
D Byte endurance 100K 1M — E/W –40C  TA  +85C
D120A E
D Byte endurance 10K 100K — E/W +85C  TA  +125C
D121 V
DRW VDD for read/write VMIN —5.5 V
† Data in “Typ” column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16F526 be driven with external clock in RC mode.
2: Negative current is defined as coming out of the pin.
3: This spec. applies to RB3/MCLR
configured as RB3 with pull-up disabled.
4: This spec. applies to all weak pull-up devices, including the weak pull-up found on RB3/MCLR
. The current value listed
will be the same whether or not the pin is configured as RB3 with pull-up enabled or as MCLR
.
5: The leakage current on the nMCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage may be measured at different input voltages.