Datasheet

PIC12F510/16F506
DS41268D-page 88 © 2007 Microchip Technology Inc.
13.3 DC Characteristics: PIC12F510/16F506 (Industrial, Extended)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating Temperature -40°C ≤ TA ≤ +85°C (industrial)
-40°C ≤ T
A ≤ +125°C (extended)
Param
No.
Sym Characteristic Min Typ† Max Units Conditions
V
IL Input Low Voltage
I/O ports
D030 with TTL buffer V
SS —0.8V VFor 4.5 ≤ VDD ≤ 5.5V
D030A V
SS —0.15VDD V otherwise
D031 with Schmitt Trigger buffer V
SS —0.15VDD V
D032 MCLR
, T0CKI VSS —0.15VDD V
D033 OSC1 (in EXTRC), EC
(1)
VSS —0.15 VDD V
D033 OSC1 (in HS) V
SS —0.3VDD V
D033 OSC1 (in XT and LP) V
SS —0.3 VDD V
V
IH Input High Voltage
I/O ports —
D040 with TTL buffer 2.0 — V
DD V4.5 ≤ VDD ≤ 5.5V
D040A 0.25 V
DD —VDD V Otherwise
+ 0.8V
D041 with Schmitt Trigger buffer 0.85 V
DD —VDD V For entire VDD range
D042 MCLR
, T0CKI 0.85 VDD —VDD V
D043 OSC1 (in EXTRC), EC
(1)
0.85 VDD —VDD V
D043 OSC1 (in HS) 0.7 V
DD —VDD V
D043 OSC1 (in XT and LP) 1.6 — V
DD V
D070 I
PUR GPIO/PORTB Weak Pull-up Current 50 250 400 μAVDD = 5V, VPIN = VSS
IIL Input Leakage Current
(2), (3)
D060 I/O ports — — ±1 μAVSS ≤ VPIN ≤ VDD, Pin at high-impedance
D062 GP3/RB3/MCLR
(5)
50 250 400 μAVDD = 5V
D061A GP3/RB3/MCLR
(4)
—+0.7±5 μAVSS ≤ VPIN ≤ VDD
D063 OSC1 — — ±5 μAVSS ≤ VPIN ≤ VDD, XT, HS and LP oscillator
configuration
Output Low Voltage
D080 V
OL I/O ports/CLKOUT — — 0.6 V IOL = 8.5 mA, VDD = 4.5V, –40°C to +85°C
D080A — — 0.6 V I
OL = 7.0 mA, VDD = 4.5V, –40°C to +125°C
D083 OSC2 — — 0.6 V I
OL = 1.6 mA, VDD = 4.5V, –40°C to +85°C
D083A — — 0.6 V I
OL = 1.2 mA, VDD = 4.5V, –40°C to +125°C
Output High Voltage
D090 V
OH I/O ports/CLKOUT
(3)
VDD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V, –40°C to +85°C
D090A V
DD – 0.7 — — V IOH = -2.5 mA, VDD = 4.5V, –40°C to +125°C
D092 OSC2 V
DD – 0.7 — — V IOH = -1.3 mA, VDD = 4.5V, –40°C to +85°C
D092A V
DD – 0.7 — — V IOH = -1.0 mA, VDD = 4.5V, –40°C to +125°C
Capacitive Loading Specs on Output Pins
D100 C
OSC2 OSC2 pin — — 15 pF In XT, HS and LP modes when external clock
is used to drive OSC1.
D101 C
IO All I/O pins — — 50 pF
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC12F510/16F506 be
driven with external clock in RC mode.
2: The leakage current on the MCLR
pin is strongly dependent on the applied voltage level. The specified levels represent normal operating
conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as coming out of the pin.
4: This specification applies when GP3/MCLR
is configured as an input with the pull-up disabled. The leakage current for the GP3/RB3/
MCLR
pin is higher than for the standard I/O port pins.
5: This specification applies when GP3/RB3/MCLR
is configured as the MCLR Reset pin function with the weak pull-up always enabled.