Datasheet

PIC16(L)F1946/47
DS41414D-page 398  2010-2012 Microchip Technology Inc.
Power-down Base Current (I
PD)
(2)
D028 — 0.1 5.0 8.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 0.1 6.0 9.0 A3.0
D028 — 22 56 63 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
— 26 58 78 A 3.0
— 27 61 88 A 5.0
D029 — 250 — — A 1.8 A/D Current (Note 1, Note 3),
conversion in progress
—250 — — A3.0
D029 — 280 — — A 1.8 A/D Current (Note 1, Note 3,
Note 4), conversion in progress
— 280 — — A 3.0
— 280 — — A 5.0
D030 — 1 — — A 3.0 LCD Bias Ladder, Low-power
—10 — — A 3.0 LCD Bias Ladder, Medium-power
—75 — — A 3.0 LCD Bias Ladder, High-power
D030 — 1 — — A 5.0 LCD Bias Ladder, Low-power
— 10 — — A 5.0 LCD Bias Ladder, Medium-power
— 75 — — A 5.0 LCD Bias Ladder, High-power
D031 — 7.6 22 25 A 1.8 Comparator, Low-Power mode
— 8.0 23 27 A3.0
D031 — 24 55 65 A 1.8 Comparator, Low-Power mode
— 26 58 80 A 3.0
— 28 60 90 A 5.0
D032A* — 2.0 — — A 1.8 Cap Sense, Low-Power mode,
CPSRM=0
—3.0 — — A3.0
D032A* — 23 — — A 1.8 Cap Sense, Low-Power mode,
CPSRM=0
— 28 — — A 3.0
— 30 — — A 5.0
30.3 DC Characteristics: PIC16(L)F1946/47-I/E (Power-Down) (Continued)
PIC16LF1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC16F1946/47
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device Characteristics Min. Typ†
Max.
+85°C
Max.
+125°C
Units
Conditions
V
DD Note
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base I
DD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base I
DD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD.
3: A/D oscillator source is F
RC.
4: 0.1 F capacitor on V
CAP (RF0).