Datasheet

PIC16F193X/LF193X
DS41364D-page 384 Preliminary  2009 Microchip Technology Inc.
29.2 DC Characteristics: PIC16F/LF1933-I/E (Industrial, Extended)
PIC16LF1933
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  T
A  +125°C for extended
PIC16F1933
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +85°C for industrial
-40°C  T
A  +125°C for extended
Param
No.
Device
Characteristics
Min. Typ† Max. Units
Conditions
V
DD Note
Supply Current (I
DD)
(1, 2)
D009
LDO Regulator
— 350 — A — HS, EC OR INTOSC/INTOSCIO (8-16 MHZ)
Clock modes with all V
CAP pins disabled
— 50 — A — All VCAP pins disabled
— 30 — A — VCAP enabled on RA0, RA5 or RA6
— 5 — A — LP Clock mode and Sleep (requires FVR and
BOR to be disabled)
D010 — 8 14 A1.8F
OSC = 32 kHz
LP Oscillator mode (Note 4),
-40°C  T
A  +85°C
—12 18A3.0
D010 — 23 38 A 1.8 FOSC = 32 kHz
LP Oscillator mode (Note 4, 5),
-40°C  T
A  +85°C
— 28 43 A 3.0
— 33 48 A 5.0
D010A — 10 18 A1.8
F
OSC = 32 kHz
LP Oscillator mode (Note 4)
-40°C  T
A  +125°C
—15 20A3.0
D010A — 24 42 A 1.8
FOSC = 32 kHz
LP Oscillator mode (Note 4, 5)
-40°C  T
A  +125°C
— 30 44 A 3.0
— 35 50 A 5.0
D011 — 125 175 A1.8F
OSC = 1 MHz
XT Oscillator mode
— 200 300 A3.0
D011 — 135 200 A 1.8 FOSC = 1 MHz
XT Oscillator mode (Note 5)
— 210 450 A 3.0
— 350 650 A 5.0
D012 — 300 400 A1.8F
OSC = 4 MHz
XT Oscillator mode
— 550 700 A3.0
D012 — 320 550 A 1.8 FOSC = 4 MHz
XT Oscillator mode (Note 5)
— 570 800 A 3.0
— 700 960 A 5.0
Note 1: The test conditions for all I
DD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to V
DD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be extended
by the formula I
R = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: 0.1 F capacitor on V
CAP (RA0).
6: 8 MHz crystal oscillator with 4x PLL enabled.